D-RP-DY-A-24 EMC Dell RecoverPoint Deploy Achievement Free Practice Exam Questions (2025 Updated)

When connecting RecoverPoint clusters over IP, it is crucial that the network infrastructure supports the data transmission requirements of RecoverPoint.

Jumbo frames are larger than standard Ethernet frames and can carry more data, reducing overhead and improving performance1.

If jumbo frames are not enabled on the IP network, the RecoverPoint clusters may fail to connect due to the inability to handle the larger data packets required for efficient replication and synchronization2.

The MTU (Maximum Transmission Unit) size also plays a role in this process.An MTU size of 9000 is often recommended for jumbo frames, but if the network devices do not support this configuration, it can lead to connection issues2.

It’s important to ensure that all network devices along the path support jumbo frames and are configured correctly to allow for the larger MTU size required by RecoverPoint clusters1.

For detailed troubleshooting steps and to confirm the exact cause of the connection failure, refer to the Dell RecoverPoint documentation or contact Dell EMC support for assistance. The information provided here is based on general knowledge of networking requirements for RecoverPoint systems and may not reflect the most recent updates or specific configurations.

Access the System Modification Wizard: Through the RecoverPoint Deployment Manager, access the System Modification wizard.

Navigate to RPA iSCSI Configuration Display: Within the wizard, proceed to the RPA iSCSI Configuration display.

Change Configuration Settings: Here, you can change the IP address and the Maximum Transmission Unit (MTU) settings for the RPA cluster1.

Save and Apply Changes: After making the necessary changes, save and apply them to update the RPA cluster’s iSCSI configuration.

It is important to note that while the IP and MTU settings can be changed, other settings such as CHAP cannot be modified through the System Modification wizard1.

Access the CLI: Use the boxmgmt account to log into the Command Line Interface (CLI) of the RecoverPoint Appliance.

Run the Command: Execute the set_user name=admin password= command to initiate the password reset process.

Set New Password: Follow the prompts to set a new password for the admin user.

This process is used when the admin password has been lost and needs to be reset.It is important to follow the correct syntax and procedure to ensure the security and integrity of the system1.

When determining the Journal volume size, the factors that must be considered are:

B. Rate of change, application data type to be replicated, and the number of snapshots to retain

Explanation:To determine the appropriate size for the Journal volume in a RecoverPoint system, several key factors need to be taken into account. These include the rate of change of the data being replicated, the type of application data (as different data types can have different change rates), and the number of snapshots to retain for recovery purposes. These factors collectively help in estimating the amount of space required for efficient journaling and replication.

References:Dell RecoverPoint for Virtual Machines 6.0.1 vSphere HTML5 Plugin Administrator's Guide, Chapter on Journal Sizing and Management.

Snapshot Writes: When application testing is performed on a remote copy, writes are directed to an XtremIO snapshot. This snapshot is a point-in-time image of the data.

Journal Behavior: These writes do not advance the Image Access log capacity because the snapshot operates independently of the Journal.The Journal is used for logging changes to the production data, not the snapshot data1.

Static Image Access Log: As a result, the Image Access log capacity remains static during the testing of the remote copy, as it is not affected by the writes to the snapshot1.

It’s important to understand that the Image Access log is designed to track changes to the replicated data in real-time.However, when operating on a snapshot, these changes are not logged in the same way, hence the Image Access log capacity does not change1.

Network Adapter Configuration: For clusters running on RecoverPoint 5.0 or later, if the WAN (Wide Area Network) and LAN (Local Area Network) are utilizing separate network adapters, it is a requirement that these adapters are configured on different subnets1.

Subnet Allocation: This involves assigning different subnet addresses to the WAN and LAN adapters to segregate traffic and ensure proper routing within the network infrastructure1.

Network Policy Compliance: Adhering to this characteristic is crucial for maintaining network policy compliance and ensuring that the RecoverPoint system functions correctly within the designed network topology1.

For more detailed information on network configuration and best practices, you can refer to the Dell EMC RecoverPoint documentation, which provides guidelines on how to set up and manage network settings for RecoverPoint clusters1.

For ensuring the highest availability for all communication within a RecoverPoint with VNX(SE) cluster using virtual RPAs in a VMware environment, it is recommended to use at least 2 virtual switches. This setup allows for redundancy and load balancing, which are crucial for maintaining high availability and preventing single points of failure.

Understanding RPA Types: RecoverPoint Appliances (RPAs) come in different generations, each with varying capabilities. Gen 6 RPAs and virtual RPAs (vRPAs) are the latest models that support advanced features and integrations.

XtremIO Integration: XtremIO is a high-performance, all-flash storage array designed for enterprise environments. It requires robust replication capabilities to ensure data protection and disaster recovery.

Supported RPA Types:

Gen 6 RPAs: These are the latest physical RPAs that support replication of XtremIO volumes. They offer enhanced performance and scalability compared to previous generations.

vRPAs: Virtual RPAs are software-based appliances that provide similar functionality to physical RPAs. They are flexible and can be deployed in virtual environments, making them suitable for XtremIO replication.

Implementation:

Step 1: Ensure that the RecoverPoint system is running the appropriate version that supports XtremIO replication.

Step 2: Configure the Gen 6 RPAs or vRPAs within the RecoverPoint system.

Step 3: Set up the replication policies and Consistency Groups to include the XtremIO volumes.

Step 4: Verify the replication setup to ensure that data is being replicated correctly between the XtremIO arrays.

Verification: After configuring the RPAs and setting up replication, monitor the system to ensure that the XtremIO volumes are being replicated as expected. Use the RecoverPoint Management Application to check the status and health of the replication.

References: This information is verified based on the official Dell RecoverPoint documentation, which details the supported RPA types and their capabilities for XtremIO replication12.

Access the Cluster Management Interface: Use a web browser to navigate to the RecoverPoint Cluster Management IP address.

Navigate to the Load Statistics: Append /info/long_term_statistics to the Cluster Management IP in the browser’s address bar.

View the Report: The RecoverPoint Cluster Load report can be viewed on this page, which provides long-term statistics including load information.

This method allows administrators to retrieve historical load data even if they did not capture the output at the time the capture load command was run1.

Access the CLI: Log into the RecoverPoint Command Line Interface (CLI) using appropriate credentials.

Run the Command: Execute the export_statistics command to gather performance data.

Save the Data: The command will output the performance data, which can then be saved to a spreadsheet.

Review and Graph: Use the spreadsheet to review the performance data and create graphs to visualize system performance over the specified time period.

The export_statistics command is used to export performance data from RecoverPoint, which can then be analyzed and graphed for a better understanding of system performance and to identify any potential issues1.

Configure the zoneincluding Unity ports and RP ports.

Perform the Unity cluster conversion(SE to EX).

Update the licensesto EX.

Confirm whether the RP cluster is addedto Unity1.

The Conversion wizard will convert both clusters on the RP system. Note that the conversion will convert the RP/SE system with the VNX arrays to a full RP system. RP/EX applies to licensing only.There are no additional configurations changes required on the VNX arrays1.

For more detailed steps and scenarios, you may refer to the “Using RP for Mid-Range Array Refresh” document available on Dell EMC Online Support, which is laid out in several scenarios1.

Deployment Manager Overview: The Deployment Manager is a tool used to install and configure RecoverPoint clusters. It guides users through various steps to ensure the proper setup and configuration of the system.

Prepare New Cluster for Connection: During this step, the Deployment Manager prepares the new cluster for connection to the existing infrastructure. This involves several sub-steps, including network configuration, validation of the environment, and ensuring that all necessary components are in place.

Adding Licenses: As part of the “Prepare New Cluster for Connection” step, new RecoverPoint licenses are added to the cluster. This is crucial because the licenses enable the functionality of the RecoverPoint system, allowing it to perform replication and recovery tasks.

Verification: After adding the licenses, the Deployment Manager verifies that the licenses are correctly applied and that the cluster is ready for the next steps in the deployment process.

References: This information is verified based on the official Dell RecoverPoint documentation, which outlines the steps and procedures for deploying and configuring RecoverPoint clusters12.

To calculate the minimum required size for the Journal volume, we can use the provided formula and input the given parameters:

Average Write Traffic: 5 Mb/s

Required Rollback Time: 24 hours (which is 24 * 60 * 60 = 86,400 seconds)

Default Parameters: Assuming the image access log percentage is 20% (which is a common default), and the reserved for marking is negligible.

Using the formula:

\text{Journal size} = 1.05 \times (\text{write traffic}) \times (\text{rollback time in seconds}) / (1 - \text{image access log percentage})Journal size=1.05×(write traffic)×(rollback time in seconds)/(1−image access log percentage)

We plug in the values:

\text{Journal size} = 1.05 \times (5 \text{ Mb/s}) \times (86,400 \text{ seconds}) / (1 - 0.2)Journal size=1.05×(5 Mb/s)×(86,400 seconds)/(1−0.2)

Converting Mb to GB (1 Mb = 1/8,000 GB):

\text{Journal size} = 1.05 \times (5/8,000 \text{ GB/s}) \times 86,400 / 0.8Journal size=1.05×(5/8,000 GB/s)×86,400/0.8

\text{Journal size} = 1.05 \times 0.000625 \text{ GB/s} \times 86,400 / 0.8Journal size=1.05×0.000625 GB/s×86,400/0.8

\text{Journal size} = 1.05 \times 54 \text{ GB} / 0.8Journal size=1.05×54 GB/0.8

\text{Journal size} = 70.875 \text{ GB}Journal size=70.875 GB

Since we need to round up to ensure we have enough space, the minimum required size for the Journal volume is approximately72.4 GB.

This calculation ensures that the Journal volume is adequately sized to handle the write traffic and maintain the required rollback time, providing a buffer for the image access log1.

When configuring zoning for RecoverPoint with VNX(SE), it is essential to follow the best practices and guidelines provided by Dell.

The zoning configuration typically involves manual setup to ensure that the RPA ports and VNX Front End (FE) ports are correctly zoned to allow for proper communication and replication processes1.

The manual method allows for precise control over the zoning configuration, which is crucial for the RecoverPoint system’s performance and reliability1.

While automatic zoning might be available in some environments, the recommended and supported method for RecoverPoint with VNX(SE) is manual zoning, as it provides the necessary customization and adherence to best practices1.

For the most accurate and detailed instructions, always refer to the latest official documentation or contact Dell EMC support directly. The information provided here is based on general knowledge of RecoverPoint systems and may not reflect the most recent updates or specific configurations.

Verify local copy licensed capacity: Ensure that the production cluster has enough licensed capacity to support an additional local copy.

Add a local copy to the Consistency Group: Use the RecoverPoint management console to add a local copy to the existing Consistency Group. This process involves selecting the Consistency Group and choosing the option to add a local copy.

Configure the local copy settings: Set up the local copy by defining the copy policy, RPO, and other relevant settings as per the application’s protection requirements.

For detailed procedures and best practices, refer to the Dell EMC RecoverPoint documentation, which provides comprehensive guidelines on adding copies to Consistency Groups and managing licensed capacities1.

Install the new RecoverPoint/EX cluster: Begin by deploying the new RecoverPoint/EX cluster at the new data center. This involves setting up the physical or virtual appliances that will form the new cluster.

Add the license to the new cluster: Once the new cluster is installed, the next step is to add the appropriate licenses. This is crucial as it enables the new cluster’s functionality within the RecoverPoint environment.

Connect the new cluster to the existing system: After the licensing is in place, the new cluster needs to be connected to the existing RecoverPoint system. This includes configuring the communication between the new and existing clusters to ensure proper replication and synchronization.

For detailed guidance on these steps, the RecoverPoint Deployment Manager can be used.It provides a suite of wizards that assist with various operations, including modifying cluster settings and adding new clusters to an existing system1.Always ensure to use the latest version of the Deployment Manager and follow the instructions provided within the tool for a non-disruptive setup1.

It is also recommended to consult the Dell RecoverPoint for Virtual Machines Installation and Deployment Guide for comprehensive instructions and best practices2.Additionally, for automation and scripting of deployment tasks, including adding new clusters, refer to the documentation on RecoverPoint for VMs Deployment Automation3.

=========================