HQT-4420 Hitachi Vantara Qualified Professional - Content Platform Installation Free Practice Exam Questions (2025 Updated)

On an HCP G10 node with six internal drives, the recommended configuration is to createa single RAID group with a single logical volume. This setup maximizes the available storagecapacity and provides a balanced approach to data protection, performance, and management simplicity. By using a single RAID group, the HCP system can efficiently manage data redundancy and integrity across all drives.

Hitachi Vantara Content Platform Installation References:

Configuring a single RAID group with a single logical volume simplifies management and provides optimal performance and redundancy, which aligns with the best practices for setting up an HCP G10 node.

When replacing an entire HCP G10 node, it is necessary to check the BIOS configuration. This ensures that the new hardware is correctly configured according to the required specifications for the HCP system. The BIOS settings need to be consistent with the rest of the cluster nodes to ensure proper functionality, performance optimization, and hardware compatibility. This check might include verifying boot order, enabling virtualization, setting appropriate hardware clock configurations, and other critical settings outlined in the "Hitachi Vantara HCP G10 Installation and Configuration Guide."QUESTION NO: 4

You are installing a HCP G10 with attached storage. The system will be networked using four 10 GbE SFP+ interfaces.

How many PCIe cards are installed in each HCP G10 node?

A. 1

B. 2

C. 3

D. 4

Answer:B

Each HCP G10 node with attached storage and networked using four 10 GbE SFP+ interfaces requires two PCIe cards. Typically, one PCIe card is allocated for network connectivity, while the other is used for storage connectivity. The cards need to support the necessary number of network interfaces and any additional connections required for attached storage. The specific configuration depends on the HCP model, but generally, two PCIe cards are sufficient to handle both networking and storage interfaces as described in the "HCP G10 Hardware Installation Guide."

The maximum number of drives supported in one HCP S10 enclosure is 60. The S10 enclosure is designed to accommodate a large number of drives to provide significant storage capacity in a relatively compact form factor. This drive density is essential for scaling storage in environments that require large data volumes. This configuration is detailed in the "HCP S10 Hardware Configuration Guide," which outlines the specifications and capacities of the S10 enclosures.

For HCP systems running version 7.2 or later, the supported VMware deployment packages are:

HCP VMware edition: This is a full-featured deployment package designed for use in production environments. It provides all the necessary components for running HCP in a VMware virtualized environment.

HCP VMware evaluation edition: This is a version meant for evaluation purposes, allowing potential users or administrators to test and familiarize themselves with HCP's capabilities in a non-production environment.

Hitachi Vantara Content Platform Installation References:

Both the "VMware edition" and "evaluation edition" are designed to be compatible with HCP version 7.2 or later, with the former being a fully supported production deployment package, while the latter is for trial or evaluation.

When installing an HCP G10 with attached storage using a VSP G1000, which is also used by several other applications, it is crucial to configure the system properly to allow shared storage use. The installation program for HCP G10 has a prompt that allows you to specify that shared storage is being used. By selecting this option, the system is informed that the VSP G1000 storage resources are shared among multiple applications, allowing for proper configuration and optimization to prevent any disruptions or conflicts. This ensures that HCP uses the storage without impacting other applications relying on the same storage system.

Hitachi Vantara Content Platform Installation References:

When setting up an HCP G10, especially in environments with shared storage configurations like the VSP G1000, the installation wizard will prompt for shared storage settings to ensure compatibility and optimal configuration.

The HCP G10 nodes useeth2andeth3ports for back-end network connections. These ports are configured for communication between the nodes and storage or within the HCP cluster itself. Back-end networks typically handle internal data traffic, replication, and synchronization, and therefore use specific dedicated ports to ensure optimal performance and separation from front-end client traffic.

Hitachi Vantara Content Platform Installation References:

The back-end network is crucial for internal HCP operations, and using eth2 and eth3 aligns with standard configurations as defined in the installation guidelines for maintaining proper data flow and redundancy.

After adding new nodes to an HCP G10 system, the following actions should be performed:

Upgrade the new nodes' software: Ensuring that the newly added nodes are running the same software version as the existing nodes is essential for compatibility and stability within the cluster.

Run the capacity balancing service: This service redistributes data across all nodes in the cluster to ensure balanced storage utilization and optimal performance, especially after the addition of new nodes.

Hitachi Vantara Content Platform Installation References:

These steps are necessary to maintain consistency, stability, and efficient use of resources within the HCP system after scaling up by adding new nodes.

When installing an HCP G10 and setting up front-end connectivity, two critical actions must be performed on each node:

Set the BMC IP Address (A):The Baseboard Management Controller (BMC) IP address must be set to allow for remote management and monitoring of each node. This is crucial for out-of-band management, especially in large data center environments where physical access to servers may be limited. Configuring the BMC IP address is typically done during the initial setup of the operating system on the HCP node.

Set the Front-End IP Address (C):The front-end IP address, which is used for client network traffic, must be configured as provided by the customer. This IP address allows each node to communicate with the client network, and it is a key part of the configuration during OS installation.

These configurations are detailed in the "HCP G10 Network Configuration Guide" and the "HCP G10 Installation and Configuration Manual," which provide step-by-step procedures for setting up both the BMC and front-end IP addresses.

To upload a software update package to an HCP S10, an SFTP (Secure File Transfer Protocol) connection is used. SFTP provides a secure way to transfer files between the administrator's machine and the HCP S10 system. This method ensures that the package is securely transmitted and prevents unauthorized access during the upload process.

Hitachi Vantara Content Platform Installation References:

The HCP S10 system requires secure methods for software updates, and SFTP is the recommended protocol for its ability to provide encryption and secure file transfer.