Weekend Sale - Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: xmaspas7

Easiest Solution 2 Pass Your Certification Exams

150-130 Brocade Certified Network Engineer 2012 Free Practice Exam Questions (2025 Updated)

Prepare effectively for your Brocade 150-130 Brocade Certified Network Engineer 2012 certification with our extensive collection of free, high-quality practice questions. Each question is designed to mirror the actual exam format and objectives, complete with comprehensive answers and detailed explanations. Our materials are regularly updated for 2025, ensuring you have the most current resources to build confidence and succeed on your first attempt.

Brocade 150-130 Premium Access     Download Demo    
Page: 1 / 2
Total 113 questions

You need to troubleshoot problems with an optic connection on a Brocade MLXe device.

What information is displayed by show optic for each port on that slot? (Choose three.)

A.

This command displays the temperature information for the optic.

B.

This command displays the transmit power information for the optic.

C.

This command displays the number of interface flaps for the optic.

D.

This command displays the receive power information for the optic.

E.

This command displays the length of the fiber cable.

You have just configured a new Multi-Chassis Trunk between two Brocade MLXe chassis.

Which protocol information will be distributed across this link?

A.

IPv6

B.

BGP

C.

RIPv2

D.

STP

Why would the IP SSH port command be used?

A.

This command is used to restrict certain port numbers from being used with SSH.

B.

This command is used to change the default port number used by SSH.

C.

This command is required before SSH will respond to any port.

D.

This command is used to set a range of port numbers to be used by SSH.

Which type of message is exchanged between switches to prevent loops and maintain loop-free topologies?

A.

LACP

B.

BPDU

C.

UDLD

D.

FDP

What happens to Ethernet frames that enter a switch with MAC learning disabled on all interfaces?

A.

AII incoming frames will be dropped.

B.

AII incoming frames will be flooded.

C.

Unicast frames will be dropped; multicast and broadcast frames will be flooded.

D.

Multicast and broadcast frames will be dropped; unicast frames will be flooded.

Which three network ranges did IETF allocate to be used as IPv4 private networks? (Choose three.)

A.

10.0.0.0/3

B.

192.168.0.0/16

C.

172.16.0.0/16

D.

172.16.0.0/12

E.

192.168.0.0/24

You have been informed a group of remote employees are unable to authenticate with the RADIUS server. From the Brocade FCX router, you enable the debug dot1x events command.

Which three events will be viewed? (Choose three.)

A.

authentications failed

B.

authentications succeeded

C.

ACLs requested by the RADIUS server.

D.

standard ACL requests

E.

extended ACL requests

What are two valid ways to represent the IPv6 address 2001:0000:0000:0200:002D:D0FF:FE48:4672? (Choose two.)

A.

2001::02:002D:D0FF:FE48:4672

B.

2001:0:0:0200:002D:D0FF:FE48:4672

C.

2001::0200:002D:D0FF:FE48:4672

D.

21::0200:002D:D0FF:FE48:4672

What are two characteristics of an IEEE 802.ID root bridge? (Choose two.)

A.

The lowest bridge ID has the highest priority for root bridge selection.

B.

The root bridge must be enabled on Brocade Layer 2 code.

C.

The bridge ID for root bridge selection is a combination of the bridge priority and MAC address.

D.

The root bridge calculates the path cost to all other switches to determine which ports will be used and which will be blocked.

Given the command output shown below:

de(config)#mirror-port ethernet 1/2/4

Brocade(config)#interface ethernet 1/2/11

Brocade(config-if-e100-11)#monitor ethernet 1/2/4 both

What do the Brocade commands accomplish?

A.

They allow all traffic on interface ethernet 1/2/11 to be replicated on interface ethernet 1/2/4 for analysis

B.

They allow ingress only traffic on interface ethernet 1/2/4 to be replicated on interface Ethernet 1/2/11 for analysis.

C.

They allow all traffic on interface ethernet 1/2/4 to be replicated on interface ethernet 1/2/11 for analysis.

D.

They allow egress only traffic on interface ethernet 1/2/4 to be replicated on interface Ethernet 1/2/11 for analysis.

What is the numeric range for standard ACL IDs?

A.

0 - 99

B.

0 -100

C.

1-99

D.

1-100

What are two benefits achieved by using a loopback interface on a Brocade router? (Choose two.)

A.

The router ID does not change.

B.

It allows remote connectivity to a router.

C.

It provides next-hop for neighbors.

D.

It does not belong to a physical interface.

You want the links between two switches to forward traffic for more than one VLAN.

What should you use to configure the inter-connected ports?

A.

load sharing

B.

tagged

C.

untagged

D.

ISL

You have lost the super-user password to your Brocade device. You need to recover the device and bypass the password, using the serial console. Which command must you issue after you interrupt the boot sequence?

A.

confreg 0x2142

B.

boot system password-bypass

C.

password recover

D.

no password

Referring to the exhibit,

Why are interfaces 1/3, 1/5 and 1/7 blocked on Switch C?

A.

Switch A is the root bridge.

B.

Switch B is the root bridge.

C.

Switch C is the root bridge.

D.

Path cost for interfaces 1/3, ly5 and 1/7 are unequal.

Which version of Simple Network Management Protocol (SNMP) supports the Advanced Encryption Standard (AES)?

A.

SNMPv1

B.

SNMPv2

C.

SNMPv2c

D.

SNMPv3

Which two access control list (ACL) types will match on TCP/UDP ports? (Choose two.)

A.

numbered standard ACLs

B.

numbered extended ACLs

C.

named standard ACLs

D.

named extended ACLs

Fiber optic cabling is immune to which type of signal degradation?

A.

attenuation

B.

noise

C.

EMI

D.

leakage

Why would the IP SSH port command be used?

A.

This command is used to restrict certain port numbers from being used with SSH.

B.

This command is used to change the default port number used by SSH.

C.

This command is required before SSH will respond to any port.

D.

This command is used to set a range of port numbers to be used by SSH.

Which QoS mechanism would you use to set the DSCP value specified of an outgoing packet?

A.

dscp-cos-mapping

B.

dscp-matching

C.

dscp-marking

D.

internal-priority-marking

Brocade 150-130 Premium Access     Download Demo    
Page: 1 / 2
Total 113 questions
Copyright © 2014-2025 Solution2Pass. All Rights Reserved