200-301 Cisco Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1 Free Practice Exam Questions (2025 Updated)
Prepare effectively for your Cisco 200-301 Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1 certification with our extensive collection of free, high-quality practice questions. Each question is designed to mirror the actual exam format and objectives, complete with comprehensive answers and detailed explanations. Our materials are regularly updated for 2025, ensuring you have the most current resources to build confidence and succeed on your first attempt.
How does a Cisco Unified Wireless network respond to Wi-Fi channel overlap?
What is the primary different between AAA authentication and authorization?
Which configuration management mechanism uses TCP port 22 by default when communicating with managed nodes?
An engineer must configure an OSPF neighbor relationship between router R1 and R3 The authentication configuration has been configured and the connecting interfaces are in the same 192.168 1.0/30 sublet. What are the next two steps to complete the configuration? (Choose two.)
Which configuration is needed to generate an RSA key for SSH on a router?
Where does a switch maintain DHCP snooping information?
Which statement about Link Aggregation when implemented on a Cisco Wireless LAN Controller is true?
What is a capability of FTP in network management operations?
How do traditional campus device management and Cisco DNA Center device management differ in regards to deployment?
Which technology must be implemented to configure network device monitoring with the highest security?
What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?
Which goal is achieved by the implementation of private IPv4 addressing on a network?
Refer to the exhibit.
Router R2 is configured with multiple routes to reach network 10 1.1 0/24 from router R1. What protocol is chosen by router R2 to reach the destination network 10.1 1 0/24?
An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any of three addresses 192.168.30.1, 192.168.3.2, 192.168.3.3 Which configuration should be used?
Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.
Refer to the exhibit.
What is a reason for poor performance on the network interface?
What is one reason to implement LAG on a Cisco WLC?
Refer to the exhibit.
The entire contents of the MAC address table are shown. Sales-4 sends a data frame to Sales-1.
What does the switch do as it receives the frame from Sales-4?
Refer to the exhibit.
Which two commands must be configured on router R1 to enable the router to accept secure remote-access connections? (Choose two)
Refer to the exhibit.
Users need to connect to the wireless network with IEEE 802. 11r-compatible devices. The connection must be maintained as users travel between floors or to other areas in the building What must be the configuration of the connection?
Refer to the exhibit.
Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?
Refer to the exhibit.
A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when the primary link goes down. Which primary route configuration must be used?
A network administrator is setting up a new IPv6 network using the 64-bit address 2001 0EB8 00C1 2200:0001 0000 0000 0331/64 To simplify the configuration the administrator has decided to compress the address Which IP address must the administrator configure?
A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must the engineer configure before entering the command to generate the RSA key?
What is a requirement when configuring or removing LAG on a WLC?
An engineer must configure R1 for a new user account. The account must meet these requirements:
* It must be configured in the local database.
* The username is engineer.
* It must use the strongest password configurable. Which command must the engineer configure on the router?
Drag and drop the TCP or UDP details from the left onto their corresponding protocols on the right.
Refer to the exhibit.
An engineer assumes a configuration task from a peer Router A must establish an OSPF neighbor relationship with neighbor 172 1 1 1 The output displays the status of the adjacency after 2 hours. What is the next step in the configuration process for the routers to establish an adjacency?
What is a requirement for nonoverlapping Wi-Fi channels?
What is a function of Opportunistic Wireless Encryption in an environment?
Refer to the exhibit.
Which command must be issued to enable a floating static default route on router A?
Refer to the exhibit.
Which network prefix was learned via EIGRP?
An engineer is configuring remote access to a router from IP subnet 10.139.58.0/28. The domain name, crypto keys, and SSH have been configured. Which configuration enables the traffic on the destination router?
A)
B)
C)
D)
Refer to the exhibit.
Which next-hop IP address does Routed use for packets destined to host 10 10.13.158?
Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.
Refer to the exhibit.
Traffic sourced from the loopback0 Interface is trying to connect via ssh to the host at 10.0.1.15. What Is the next hop to the destination address?
A network engineer must configure two new subnets using the address block 10 70 128 0/19 to meet these requirements:
• The first subnet must support 24 hosts
• The second subnet must support 472 hosts
• Both subnets must use the longest subnet mask possible from the address block
Which two configurations must be used to configure the new subnets and meet a requirement to use the first available address in each subnet for the router interfaces? (Choose two )
Refer to the exhibit.
Host A sent a data frame destined for host D
What does the switch do when it receives the frame from host A?
Refer to the exhibit.
An engineer is configuring a new router on the network and applied this configuration. Which additional configuration allows the PC to obtain its IP address from a DHCP server?
What is an expected outcome when network management automation is deployed?
Refer to the exhibit.
Packets received by the router from BGP enter via a serial interface at 209 165 201 1 Each route is present within the routing table Which interface is used to forward traffic with a destination IP of 10.1.1.19?
Which type of network attack overwhelms the target server by sending multiple packets to a port until the half-open TCP resources of the target are exhausted?
Which action is taken by the data plane within a network device?
What is the function of the controller in a software-defined network?
Refer to the exhibit.
Traffic that is flowing over interface TenGigabitEthernet0/0 experiences slow transfer speeds. What is the reason for the issue?
A Cisco engineer must configure a single switch interface to meet these requirements
• accept untagged frames and place them in VLAN 20
• accept tagged frames in VLAN 30 when CDP detects a Cisco IP phone
Which command set must the engineer apply?
A)
B)
C)
D)
Refer to the exhibit.
Which configuration enables DHCP addressing for hosts connected to interface FastEthernetO/1 on router R4?
Refer to the exhibit.
Switch A is newly configured. All VLANs are present in the VLAN database. The IP phone and PC A on Gi0/1 must be configured for the appropriate VLANs to establish connectivity between the PCs. Which command set fulfills the requirement?
A)
B)
C)
D)
What is a function of a Next-Generation IPS?
Which protocol uses the SSL?
What is the purpose of the ip address dhcp command?
Refer to the exhibit.
Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10.10.24?
Refer to the exhibit.
Router R1 resides in OSPF Area 0. After updating the R1 configuration to influence the paths that it will use to direct traffic, an engineer verified that each of the four Gigabit interfaces has the same route to 10.10.0.0/16. Which interface will R1 choose to send traffic to reach the route?
An engineer must configure Interswitch VLAN communication between a Cisco switch and a third-party switch. Which action should be taken?
What is an advantage of Cisco DNA Center versus traditional campus device management?
Which technology is appropriate for communication between an SDN controller and applications running over the network?
What uses HTTP messages to transfer data to applications residing on different hosts?
A network administrator is asked to configure VLANS 2, 3 and 4 for a new implementation. Some ports must be assigned to the new VLANS with unused remaining. Which action should be taken for the unused ports?
Which WLC port connects to a switch to pass normal access-point traffic?
A network analyst is tasked with configured the date and time on a router using EXEC mode. The date must be set to 12:00am. Which command should be used?
