Huawei H12-893_V1.0 Practice Test Questions Answers

Traditional data center networks (DCNs) often suffer from single points of failure, limited scalability, and traffic bottlenecks. Both M-LAG and stacking address these issues, but their suitability for 24/7 service continuity differs.

M-LAG Benefits:M-LAG (Multi-Chassis Link Aggregation) on Huawei CE switches allows two devices to act as a single logical switch, providing active-active forwarding, high availability, and rapid failover (e.g., via peer-link synchronization). It supports non-stop service during device failures, making it ideal for 24/7 continuity.

Stacking Benefits:Stacking combines multiple switches into a single logical unit, sharing a control plane. While it improves scalability and simplifies management, a stack master failure can disrupt the entire stack unless redundancy is perfectly configured, potentially affecting service continuity.

Comparison:M-LAG’s decentralized design and real-time synchronization offer better fault isolation and recovery compared to stacking, where a master switch failure impacts the stack. Huawei documentation highlights M-LAG’s superiority for high-availability scenarios like 24/7 operations.

The statement isTRUE (A)because M-LAG is indeed a better choice than stacking for ensuring 24/7 service continuity due to its robust failover and redundancy features.References:Huawei CloudEngine Series Switch Configuration Guide – M-LAG vs. Stacking; HCIP-Data Center Network Training – High Availability Solutions.

Centralized gateway deployment using BGP EVPN in Huawei’s data center networks (e.g., CloudFabric) involves a gateway handling Layer 3 routing for VXLAN overlays. Let’s evaluate each statement:

A. When configuring a VTEP, you need to create a Layer 2 BD and bind a VNI to the Layer 2 BD:A Bridge Domain (BD) is a Layer 2 broadcast domain in VXLAN, and a Virtual Network Identifier (VNI) is bound to it to segment traffic. This is a standard step when configuring a VXLAN Tunnel Endpoint (VTEP) to map the overlay network.TRUE.

B. A VXLAN tunnel is identified by a pair of VTEP IP addresses and can be established if the local and remote VTEP IP addresses are reachable to each other at Layer 3:VXLAN tunnels are established between VTEPs using their IP addresses as endpoints. Layer 3 reachability (e.g., via underlay routing) is required for tunnel establishment.TRUE.

C. When BGP EVPN is used to dynamically establish a VXLAN tunnel, the local and remote VTEPs first establish a BGP EVPN peer relationship and then exchange BGP EVPN routes to transmit VNI and VTEP IP address information. A VXLAN tunnel is then dynamically established between them:In BGP EVPN, VTEPs establish a BGP peer relationship, exchange routes (e.g., Type 2 for MAC/IP or Type 3 for multicast), and share VNI and VTEP IP details, enabling dynamic tunnel setup.TRUE.

D. When configuring a VTEP, you need to create an EVPN Instance in the Layer 2 BDand configure an RD for the local EVPN instance. You do not need to configure an RT:An EVPN Instance (EVI) is created within a BD, and a Route Distinguisher (RD) is configured to make routes unique. However, Route Targets (RTs) are also required to control route import/export between EVPN peers, ensuring proper VNI and route distribution. Stating that RT configuration is not needed is incorrect, as RTs are essential for BGP EVPN operation.FALSE.

Thus,Dis the false statement because RT configuration is necessary in centralized gateway deployment with BGP EVPN.References:Huawei CloudFabric Data Center Network Solution – BGP EVPN Configuration; HCIP-Data Center Network Training – EVPN Gateway Deployment.

In Huawei’s Data Center Network (DCN) architecture, particularly with the CloudFabric solution, the spine-leaf topology is a common design for scalable and efficient data centers. VXLAN (Virtual Extensible LAN) is used to create overlay networks, enabling large-scale multi-tenancy and flexible workload placement.

Spine Nodes’ Role:In this architecture, spine nodes act as the backbone, interconnecting leaf nodes (which connect to servers, storage, or other endpoints) and facilitating high-speed, non-blocking communication. Spine nodes typically handle Layer 3 routing and serve as VXLAN tunnel endpoints (VTEPs) or connect to devices that do, integrating the physical underlay with the VXLAN overlay network.

Connection to VXLAN:Spine nodes ensure that traffic from various network devices (via leaf nodes) is routed efficiently across the VXLAN fabric. They provide the high-bandwidth, low-latency backbone required for east-west traffic in modern data centers, supporting VXLAN encapsulation and decapsulation indirectly or directly depending on the deployment.

Thus, the statement isTRUE (A)because spine nodes play a critical role in connecting the underlay network (various devices via leaf nodes) to the VXLAN overlay, as per Huawei’s DCN design principles.References:Huawei CloudFabric Data Center Network Solution White Paper; HCIP-Data Center Network Training Materials – VXLAN and Spine-Leaf Architecture.

A vNIC (virtual Network Interface Card) is a software-emulated network interface used by virtual machines to communicate over a virtual or physical network. The statement’s reference to “bit stream mode” is ambiguous but likely implies raw, low-level bit transmission without higher-layer processing.

vNIC Functionality:A vNIC operates at a higher abstraction level than physical NICs. It interfaces with the hypervisor’s virtual switch (e.g., Open vSwitch in Huawei environments) and handles data in frames or packets (e.g., Ethernet frames), not just raw bit streams. The hypervisor or host NIC handles the physical bit stream transmission.

Data Transmission:vNICs support various modes depending on configuration (e.g., VirtIO, SR-IOV passthrough), transmitting structured data (frames/packets) rather than solely raw bits. Bit stream transmission is a physical-layer task, not the vNIC’s sole mode.

Thus, the statement isFALSE (B)because a vNIC does not transmit dataonlyin bit stream mode; it handles higher-level data structures, with bit-level transmission managed by underlying hardware.References:Huawei HCIP-Data Center Network Training – Virtualization Networking; FusionCompute Networking Guide.

In Huawei’s CloudFabric computing scenario, VM service traffic involves virtualized environments with VXLAN overlays and traditional VLANs. Let’s evaluate each statement:

A. Traffic inside a fabric is VXLAN encapsulated:This is true. Within a CloudFabric network, VXLAN encapsulation is used to transport traffic across the fabric, enabling overlay networking for VMs.TRUE.

B. Inter-VPC traffic must pass through the firewall:This is false. Inter-VPC (Virtual Private Cloud) traffic can be routed directly between VPCs using a gateway or router (e.g., with EVPN Type 5 routes) without necessarily passing through a firewall, depending on security policies. Firewalls are optional for inter-VPC traffic, not mandatory.FALSE.

C. Traffic between VAS devices and service leaf nodes is VLAN encapsulated:This is true. Value-Added Services (VAS) devices (e.g., load balancers) often connect to service leaf nodes using VLAN encapsulation, especially in traditional or hybrid deployments.TRUE.

D. Traffic between vSwitches on virtual servers and server leaf nodes is VLAN encapsulated:This is true. Traffic from virtual switches (vSwitches) on hypervisors to physical server leaf nodes typically uses VLAN encapsulation over the physical NICs, before VXLAN overlay if applicable.TRUE.

Thus,Bis the false statement because inter-VPC traffic does not always require a firewall.References:Huawei CloudFabric Data Center Network Solution – Traffic Engineering; HCIP-Data Center Network Training – VM Traffic.