H12-811_V1.0 Huawei HCIA-Datacom V1.0 Exam Free Practice Exam Questions (2026 Updated)

In PPP (Point-to-Point Protocol) authentication, if the authentication fails, the authenticator sends an Authenticate-Reject message.

Option A (Incorrect - Authenticate-Ack): Sent when authentication is successful.

Option B (Incorrect - Authenticate-Reply): Not a valid PPP authentication message.

Option C (Correct - Authenticate-Reject): Sent when authentication fails, and the connection is rejected.

Option D (Incorrect - Authenticate-Nak): Used for PPP negotiation, not authentication failure.

Thus, the correct answer is C.

When HostA wants to send data to HostC, the following steps occur:

HostA checks if HostC is in the same subnet:

HostA and HostC are in different network segments, meaning HostA must send the packet to its default gateway (RTA, G0/0/0) to reach HostC.

HostA needs the MAC address of its gateway (RTA G0/0/0):

Since ARP (Address Resolution Protocol) is used to resolve IP to MAC addresses, HostA will send an ARP Request to obtain the MAC address of G0/0/0 of RTA.

RTA forwards the packet to HostC:

Once HostA sends the packet to RTA (using G0/0/0 ' s MAC), RTA will route it to the correct network segment and send it to HostC through G0/0/1.

Why the Other Options Are Incorrect:

Option A (HostC) - Incorrect:

HostA does not send an ARP request for HostC because HostC is in a different subnet.

Option B (G0/0/1 of RTA) - Incorrect:

HostA only communicates with its directly connected gateway (G0/0/0), not G0/0/1.

Option C (SWA) - Incorrect:

Switches (SWA, SWB) operate at Layer 2 and do not require ARP.

Final Answer: D (G0/0/0 of RTA)

Comprehensive Explanation: The IEEE 802.11g standard operates exclusively in the 2.4 GHz frequency band, offering data rates up to 54 Mbps. Other standards, such as 802.11a, operate in the 5 GHz band, while 802.11n and 802.11ax support both 2.4 GHz and 5 GHz frequency bands, making 802.11g the only standard in this list that is limited to 2.4 GHz.

The tracert (Trace Route) command is a network diagnostic tool used to trace the path that packets take from the source device to the destination.

It works by sending ICMP Echo Requests (or UDP packets) with increasing TTL (Time-To-Live) values and recording responses from each hop along the way.

This helps network administrators identify routing issues, network delays, and connectivity problems in the forwarding path.

The command is commonly used in Huawei VRP to diagnose network latency or packet loss between different nodes.

Thus, the correct answer is A (TRUE).

The command defines a static route to the network 10.0.12.0 with a 255.255.255.0 subnet mask, using 192.168.1.1 as the next-hop address. Static routes are manually set routes with fixed paths, and by default, they have higher priority than dynamic routes, but the specific preference value depends on configuration. This setup enables targeted routing for traffic towards the specified destination​.

Comprehensive Explanation: It is possible for the load balancing modes at both ends of an Eth-Trunk (Ethernet Trunk) to be different, as long as the devices at both ends support the different modes. Load balancing modes control how traffic is distributed across multiple links in the trunk. Although the modes may differ, they must be compatible in terms of ensuring that traffic is appropriately handled across the multiple physical interfaces bundled in the trunk.

Comprehensive Explanation: Router Advertisement (RA) packets in IPv6 are part of the Neighbor Discovery Protocol, which uses ICMPv6 (Internet Control Message Protocol for IPv6). RA messages are sent by routers to inform hosts about the presence of routers on the network and provide them with information needed for stateless address auto-configuration, such as the network prefix and default gateway.

Comprehensive and Detailed In-Depth Explanation:

IPv6 abbreviation rules allow replacing consecutive zeros with ::.

Correct answer: C (2FFF:0DAC:ABEF:0000:0000:CDAA:0732)

B (Correct) - HTTP: Uses TCP port 80 for web traffic.

C (Correct) - FTP: Uses TCP ports 20/21 for file transfer.

A (Incorrect) - TFTP: Uses UDP port 69, not TCP.

D (Incorrect) - Ping: Uses ICMP, which is neither TCP nor UDP.

Thus, the correct answers are B and C.

Comprehensive Explanation: Hybrid interfaces are capable of carrying both tagged and untagged VLAN frames. They can remove VLAN tags from certain VLANs when sending data frames, depending on the configuration. The command port hybrid untagged vlan x allows a hybrid interface to transmit data frames for VLAN x without a tag, while still tagging other VLANs as required. Hybrid interfaces are flexible and can be used for trunking, but unlike pure trunk ports, they do not always require VLAN tags.

When a Windows host first boots up and does not have an IP address, it sends a DHCP Discover message to find a DHCP server.

The source IP address of this packet is 0.0.0.0, meaning the host does not yet have an assigned IP.

The destination IP address is 255.255.255.255, which is a broadcast address.

Option A (Incorrect - 127.0.0.1): This is the loopback address, used for internal testing.

Option B (Incorrect - 169.254.2.33): This belongs to the APIPA (Automatic Private IP Addressing) range, assigned when a DHCP server is unavailable.

Option C (Correct - 0.0.0.0): The correct source IP for the initial DHCP Discover packet.

Option D (Incorrect - 255.255.255.255): This is used as the destination IP for broadcasting, not the source.

Thus, the correct answer is C.

Detailed Explanation:In this scenario, the MAC address 00e0-fc99-9999 is associated with multiple IP addresses through dynamic ARP learning, indicating that the host’s IP has changed several times. The ARP table on the switch shows multiple entries with different IPs mapped to the same MAC address, which is common when a device frequently updates its IP. As ARP is a dynamic protocol, these entries reflect the device ' s current and past IP associations. (Reference: HCIA-Datacom Training Material, ARP Operation and IP-MAC Mapping)

Comprehensive Explanation: In STP (Spanning Tree Protocol), ports can be in several states, including:

Discarding: The port is not forwarding traffic, either because it is in a blocking state or not participating in active forwarding.

Listening: The port is processing BPDUs and is preparing to transition to either the learning or forwarding state. No data frames are forwarded during this state.

Forwarding: The port is actively forwarding traffic as part of the active network topology.

The " Disabled " state is not part of the STP protocol but rather represents a port that is administratively shut down or not participating in the STP process.

Comprehensive and Detailed Explanation:

RADIUS (Remote Authentication Dial-In User Service) is a widely used AAA protocol for:

Authentication (verifying user credentials).

Authorization (determining access level).

Accounting (logging user activity).

It uses UDP (ports 1812/1813 or 1645/1646) and is common in enterprise networks.

✅ Reference: HCIA-Datacom Security Guide – AAA & RADIUS Overview