350-601 Cisco Implementing Cisco Data Center Core Technologies (350-601 DCCOR) Free Practice Exam Questions (2025 Updated)
Prepare effectively for your Cisco 350-601 Implementing Cisco Data Center Core Technologies (350-601 DCCOR) certification with our extensive collection of free, high-quality practice questions. Each question is designed to mirror the actual exam format and objectives, complete with comprehensive answers and detailed explanations. Our materials are regularly updated for 2025, ensuring you have the most current resources to build confidence and succeed on your first attempt.
Refer to the exhibit. An FCoE-attached storage connects to a Cisco Nexus 9000 Series Switch on interface ethernet1/12. After the configuration was performed. VSAN 200 failed to activate on the vfc interface. Which configuration action must be performed to bring up VSAN 200?
Which storage solution allows multiple users to access files directly on a storage array over a LAN network?
Anetwork engineer must configure a vPC on a pair of Cisco Nexus switches connected to a third-party load balancer. The connection must meet these requirements:
* The port channel must be negotiated with the load balancer via an open standards protocol.
* Traffic that is sent directly to the physical MAC address of the other peer switch must be forwarded locally by the receiving switch.
Which command set accomplishes these goals?
What is the impact of upgrading the firmware version of the Cisco MDS 9200i Series Switch?
An engineer must configure HSRP protocol on two cisco nexus 9000 series switches running a virtual port channel in addition, the HSRP implementation must meet these requirements:
Drag and drop the commands from the the right to complete a configuration of the HSRP on the left. The commands are used more than once. Not all commands are used
All logins to a Cisco Nexus 9000 Series Switch must pass through the TACACS+ server at IP address 192.168.10.10. The configuration must meet these requirements:
• The TACACS+ server must be used for SSH and Telnet.
• The TACACS+ server key must be Cisco123!.
• Management VRF must be used for connectivity.
• The deployment must fail back to local credentials if the TACACS+ server fails to respond within 30 seconds.
Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the configuration. Not all code snippets are used.
An engineer must configure device aliases for a Cisco MDS 9000 Series Switches-based SAN fabric. The configuration must meet these requirements:
The engineer must be prompted before the changes are committed to the database
Pending changes must be explicitly displayed on the console.
Which command accomplishes this task?
An engineer builds a new Cisco ACI fabric Which VLAN must be configured as the infrastructure VLAN during the Cisco APIC setup script?
Refer to the exhibit. An engineer must create a scheduler task on a Cisco Nexus 9000 Series Switch at 06:00 AM. The task must save the running configuration to a file in the bootflash, then transfer the file from the bootflash to a TFTP server Which command must the scheduler task run after the running configuration is copied to the bootflash?
An engineer is implementing the Cisco ACI fabric and must create two different vPCs from leaf switches A and B. The vPCs are deployed as follows:
vPC 1 encompasses ports Eth 1 /1 on leaf A and B and connects to server 1.
vPC 2 encompasses port Eth1/2 on leaf A and B and connects to server 2.
A leaf switch profile listing leaves A and B is already configured Which ACI object must be created to meet these requirements?
AN engineer is asked to modify an overridden policy by changing the number of FCNS database entries to 1500 and then generable a massage. What configuration will accomplish this task?
A)
B)
C)
D)
What is a benefit of independent resource scaling in Cisco
HyperFlex hybrid architecture?
An engineer must configure Protocol Independent Multicast on two Cisco Nexus 9000 Series Switches. The engineer must ensure that the chosen rendezvous point (RP) uses a mapping agent and only supports one RP per multicast group. Which type of RP must be used on both switches to meet these requirements?
Refer to the exhibit. A Cisco data center environment is implemented with vPC. The web server replies using the SVI MAC address as the Layer 2 header instead of the HSRP MAC address on VLAN 23. This behavior causes packet drops on the Cisco Nexus 9000 Series Switches due to the vPC loop prevention mechanism The requirement is for the vPC feature to allow N9K_1 and N9K_2 to forward traffic between the NAS server and the web server, even if the HSRP's MAC address is not used on Layer 2 headers for VLAN 23. Which feature must be used to accomplish this goal?
Refer to the exhibit. In a Cisco ACI fabric, the status of interface Eth1/1 changes frequently. Which set of actions configures the fabric to disable Eth1/1 when the port flaps more than 10 times within 1 minute?
An engineer must configure a user role interface policy on a Cisco Nexus 9000 Series Switch. The role must prevent access to interface FC3/2 but allow access to interface FC3/1. Which
set of actions must be taken to accomplish this goal?
An engineer must configure a Cisco MDS 9000 Series Switch for traffic analysis from the storage array. The storage array is connected to the interface fc2/1 in VSAN 10 and the traffic analyzer to fc4/2. The capture file must include ingress and egress traffic between the switch and the storage array. Also, only traffic in VSAN 10 must be captured. Which configuration set meets these requirements?
An engineer needs to create a new user in the local user database on Cisco UCS Fabric Interconnect. The user needs permissions to change the following configuration inside UCS Manager version 3.1:
• vNIC and vHBA profiles
• Fan speed and power redundancy profile of UCS Manager
Which two roles must be assigned to a user to achieve this goal? (Choose two.)
Which two statements describe the process of upgrading an EPLD on a Cisco MUS 9000 Series Switch? (Choose two)
A network engineer must create an EEM script that saves a copy of the running configuration on bootflash and writes a message to syslog when a user saves the configuration to a Cisco Nexus switch. Which configuration set should be applied to complete this task?
