H12-811_V1.0 Huawei HCIA-Datacom V1.0 Exam Free Practice Exam Questions (2025 Updated)

Restoring factory defaults on an AR2200 router requires both clearing the current configuration and resetting saved configurations. These steps ensure that any custom settings are removed, reverting the router to its original state. Simply restarting or specifying a startup file without clearing configurations would not remove custom settings​.

Statement A (Correct): DR and BDR must form an adjacency relationship to maintain routing information exchange.

Statement B (Incorrect): The router with the higher priority is elected as DR, not the lower one.

Statement C (Incorrect): DR is elected by routers within a broadcast/multi-access network, not necessarily all routers in the same network segment.

Statement D (Correct): If two routers have the same priority, the one with the higher Router ID becomes the DR.

OSPF does not use TCP or UDP because it has its own reliable transmission mechanisms.

OSPF packets are encapsulated directly in IP packets using protocol number 89.

TCP (A) is used for connection-oriented communication, but OSPF does not rely on it.

UDP (C) is used for connectionless communication, but OSPF does not use it.

HTTP (B) is an application-layer protocol and irrelevant here.

Thus, the correct answer is D (IP).

The PVID (Port VLAN ID) for a hybrid port refers to the VLAN that is assigned to untagged traffic. In this case, VLAN 4 is specified as untagged, making it the PVID for this interface. Traffic received without a VLAN tag is associated with VLAN 4 upon entering the switch​.

The root path cost is calculated by summing the costs of each port on the path from the root bridge to the receiving port. In this case, assuming each link has a cost of 200, the total cost to reach the root from the indicated port would be 600, reflecting three hops from the root bridge​.

The tracert (Trace Route) command is a network diagnostic tool used to trace the path that packets take from the source device to the destination.

It works by sending ICMP Echo Requests (or UDP packets) with increasing TTL (Time-To-Live) values and recording responses from each hop along the way.

This helps network administrators identify routing issues, network delays, and connectivity problems in the forwarding path.

The command is commonly used in Huawei VRP to diagnose network latency or packet loss between different nodes.

Thus, the correct answer is A (TRUE).

Detailed Explanation:OSPF (Open Shortest Path First) uses protocol number 89 at the network layer. This distinguishes OSPF packets from other protocols such as TCP (protocol number 6) and ICMP (protocol number 1) .

Comprehensive and Detailed Explanation:

The TTL field is 8 bits long, allowing values from 0 to 255 (A is correct).

The TTL prevents routing loops by discarding packets with TTL=0 (B is correct).

Each Layer 3 device (router) that forwards the packet decrements TTL by 1 (C is correct).

If TTL reaches zero, the router drops the packet and sends an ICMP Time Exceeded message.

✅ Reference: HCIA-Datacom Network Principles Guide – IP Packet Structure

Detailed Explanation:The default Router Dead Interval in OSPF is 40 seconds for broadcast and point-to-point networks. This interval defines the time period a router waits to receive hello packets before declaring a neighbor as down. (Reference: HCIA-Datacom Training Material, OSPF Hello and Dead Intervals)

Detailed Explanation:With SNMP (Simple Network Management Protocol), a Network Management System (NMS) can both monitor device status and configure settings on managed devices using SNMP Set commands. (Reference: HCIA-Datacom Training Material, SNMP Protocol Functions)

The command defines a static route to the network 10.0.12.0 with a 255.255.255.0 subnet mask, using 192.168.1.1 as the next-hop address. Static routes are manually set routes with fixed paths, and by default, they have higher priority than dynamic routes, but the specific preference value depends on configuration. This setup enables targeted routing for traffic towards the specified destination​.

Dynamic Routing Protocol Purpose:A dynamic routing protocol's primary function is to dynamically generate and maintain routing tables by learning and sharing routing information between routers in real time. This ensures efficient path selection and adaptation to network changes​​.

Analysis of Options:

Option A: "Generate an IP address" is unrelated to routing protocols; IP address assignment is handled by DHCP or manual configuration.

Option B: "Manage routers" is inaccurate, as dynamic routing protocols do not manage router hardware or administrative tasks.

Option C: "Generate a routing table" is correct because routing protocols dynamically compute and update routing tables based on network topology changes.

Option D: "Control the status of router interfaces" refers to interface management, which is not a function of dynamic routing protocols.

Correct Answer:The main function of a dynamic routing protocol is C (Generate a routing table).

Router Initialization:

When a router boots up, it attempts to load its configuration file from the default save directory to initialize.

If the configuration file is missing, the router defaults to preconfigured parameters to ensure basic functionality.

Default Parameters:

These parameters include IP routing, interface defaults, and system-level settings. They allow network administrators to connect and manually configure the router.

Why Other Options Are Incorrect:

B: The "initial configuration file" refers to the manually created file, which may not exist.

C: The "current configuration file" is used during runtime but does not persist through reboots if unsaved.

D: A "new configuration file" must be manually created and does not exist by default.

References: HCIA-Datacom V1.0 Certification Guide, Chapter 2: Device Initialization.

In the IP header at the network layer, the Protocol field specifies the transport layer protocol in use. The protocol number for UDP is 17, not 6. Protocol number 6 is reserved for TCP. This field allows IP packets to be correctly processed by the appropriate transport-layer protocol at the receiving device​.