H12-821_V1.0 Huawei HCIP-Datacom-Core Technology V1.0 Free Practice Exam Questions (2026 Updated)

Comprehensive and Detailed Step-by-Step Explanation:

IS-IS Three-Way Handshake:

IS-IS uses a three-way handshake to establish neighbor relationships.

This process is applied on both point-to-point (P2P) and broadcast network types to confirm bidirectional communication.

P2P Networks:

Routers directly exchange IS-IS Hello (IIH) packets to establish adjacency.

Broadcast Networks:

IS-IS also uses the three-way handshake on broadcast networks to ensure that the Designated Intermediate System (DIS) election and adjacency formation are correct.

Comprehensive and Detailed Step-by-Step Explanation:

1. Overview of BFD Optimization:

BFD (Bidirectional Forwarding Detection) is a protocol that provides rapid detection of link failures.

Optimizing BFD involves adjusting parameters to balance between detection speed and network stability.

2. Analysis of Each Statement:

Option A: After a high priority is configured for BFD packets, BFD packets are preferentially forwarded.

Correct (True Statement).

High priority ensures that BFD packets are not delayed or dropped under congestion, improving detection accuracy.

Option B: To quickly learn about the network status and performance requirements, you can set the interval for sending BFD packets to the minimum value.

Incorrect (False Statement).

Setting the interval to the minimum value can lead to excessive BFD session flapping, which may overload the network or cause instability. The interval should be configured based on network requirements and conditions, rather than set to the minimum.

Option C: On a live network, some devices switch traffic only when a BFD session changes to the Up state... configure a delay to compensate for the time difference.

Correct (True Statement).

This is a valid optimization to avoid issues caused by timing mismatches between BFD and routing protocols.

Option D: If a BFD session flaps, master/backup switchovers are frequently performed... set the WTR time.

Correct (True Statement).

The WTR (Wait to Restore) timer helps stabilize BFD by delaying session recovery after a flap, reducing the risk of frequent switchovers.

3. Summary:

The false statement is B, as setting the BFD packet interval to the minimum can destabilize the network.

When routes are imported into BGP using the import-route command, the origin attribute is set to incomplete by default. This indicates that the route's origin is not known or is from an external source, as opposed to being explicitly learned through an IGP (IGP) or EGP (EGP) protocol ​.

Attributes such as community, tag, and origin can be directly referenced in the apply clause of a route-policy. However, IP-prefix is not an attribute but a prefix list used for matching, and it cannot be directly applied ​.

Secure access channels include protocols that encrypt the transmitted data to protect against interception or unauthorized access. HTTPS (HyperText Transfer Protocol Secure) ensures data encryption over web communications, while SFTP (Secure File Transfer Protocol) provides secure file transfer by utilizing SSH for data encryption. Telnet and SNMPv2, on the other hand, lack robust encryption and are considered insecure. Huawei security standards highlight the importance of encrypted communication to prevent data leaks ​.

According to BGP route selection rules, a higher Local_Pref value indicates a more preferred route. This rule is used to influence traffic flow within an autonomous system (AS), giving preference to routes with a higher Local_Pref for outgoing traffic ​.

Comprehensive and Detailed Step-by-Step Explanation:

Blackhole Route Issue in BGP:

In IBGP, the next hop of a route learned from an EBGP peer is not changed by default. If an IBGP peer cannot reach the next hop, blackhole routes may occur.

To prevent this, the peer next-hop-local command is used to set the next hop to the local router's IP address.

Other Commands:

peer mpls-local-ifnet: Used in MPLS networks to set the next hop as the local interface address.

peer private-nexthop: Allows advertising private IP addresses as the next hop.

peer next-hop-invariable: Ensures the next hop is not modified during route advertisement, which is the opposite of what is required here.

A is false – Ports in MSTP can have different roles and states in different MSTIs. Each MSTI can independently elect a root and compute its own topology, which results in different port states per MSTI.

B is true – MSTIs use the same spanning tree algorithm as STP (and RSTP) for calculating the spanning tree topology.

C is true – Each MSTI may have a different root bridge and separate topology, depending on VLAN mappings.

D is true – MSTIs do not independently send BPDUs; only MSTI 0 (CIST) actually sends BPDUs, and information about other MSTIs is encapsulated within it. So the statement is worded to test conceptual understanding, but not incorrect in MSTP context as framed.

Reference from Huawei HCIP-Datacom-Core Technology Study Guide:

“MSTP allows different MSTIs to have different topologies. A port may be forwarding in MSTI 1 but blocking in MSTI 2. This independence improves VLAN-based traffic engineering.”

(Chapter: MSTP Concepts – Section: MSTI Behavior and Port Roles)

ICMPv6 messages are classified into two types: error messages (e.g., Destination Unreachable, Time Exceeded) and informational messages (e.g., Echo Request, Echo Reply). This classification is fundamental to ICMPv6's operation ​.

 Edge Port Behavior

An edge port transitions directly to the Forwarding state but reverts to participating in RSTP calculations if it receives a valid configuration BPDU. Thus, statement C is false.

 HCIP-Datacom-Core Reference

The behavior of edge ports and their transitions are discussed in the RSTP enhancement sections​​.

When STP and RSTP coexist in a network, RSTP switches will downgrade their operation to STP to ensure compatibility. However, this disables RSTP's rapid convergence features, as the protocol behaves like STP to maintain interoperability ​.

Route summarization in OSPF is restricted to specific routers: Area Border Routers (ABRs) and Autonomous System Boundary Routers (ASBRs). These devices perform summarization to reduce routing table size and minimize advertised routing information between areas or across AS boundaries. Regular routers cannot perform route summarization, making this statement false ​.

Comprehensive and Detailed Step-by-Step Explanation:

1. IPv6 and Neighbor Discovery Protocol (NDP):

In IPv4, a host uses ARP (Address Resolution Protocol) to map an IP address to a MAC address for communication.

In IPv6, ARP is not used. Instead, IPv6 uses the Neighbor Discovery Protocol (NDP) for address resolution.

2. Why the Statement is FALSE:

IPv6 does not use ARP for resolving link-layer addresses.

IPv6 uses NDP, which operates through ICMPv6 messages to perform the equivalent function.

3. Summary:

The statement is FALSE because IPv6 uses NDP, not ARP, to obtain the link-layer address of the destination host.

Comprehensive and Detailed Step-by-Step Explanation:

Analysis of the OSPF Neighbor State:

Router ID 10.0.5.5:

On interface 10.0.235.2 (GigabitEthernet0/0/1), the neighbor state is Full, indicating that adjacency is established.

The Designated Router (DR) is 10.0.235.5, which is the same as the neighbor's address.

Router ID 10.0.4.4:

On interface 10.0.24.2 (Serial1/0/1), the neighbor state is also Full, meaning adjacency is established.

The DR/BDR election status shows None, indicating that the interface is on a point-to-point link where DR/BDR election does not apply.

Validation of Each Option:

Option A: Correct. The DR IP address is explicitly shown as 10.0.235.5.

Option B: Correct. The neighbor state for both 10.0.5.5 and 10.0.4.4 is Full, confirming adjacency is established.

Option C: Incorrect. DR/BDR elections are irrelevant on point-to-point links like Serial1/0/1.

Option D: Correct. The Router IDs of R2's neighbors are explicitly listed as 10.0.5.5 and 10.0.4.4.

The Originator ID in a BGP route represents the Router ID of the device that originally advertised the route into the BGP domain. Since RTA originates the route 10.1.1.0/24 into the BGP process, the Originator ID in the route received by RTD will be set to 1.1.1.1 ​.

 IS-IS Overview: Intermediate System to Intermediate System (IS-IS) is a link-state routing protocol. Routers exchange Link State Packets (LSPs) to maintain a synchronized link-state database. These LSPs are categorized into Level-1 LSPs (intra-area routing) and Level-2 LSPs (inter-area routing). Both types share the same packet format.

HCIP-Datacom-Core Technology Training Material (IS-IS LSPs and Packet Structure)​​.

 LSP ID Format: The LSP ID uniquely identifies each LSP and ensures accurate routing information. It comprises the following components:

System ID (C): A 6-byte identifier assigned to each router, derived from the router's NET (Network Entity Title). This identifier ensures unique identification of routers within the IS-IS domain.

Pseudonode ID (B): Assigned when a router acts as a Designated Intermediate System (DIS) on a broadcast network. It differentiates LSPs generated by the DIS from other routers.

LSP Number (A): A 1-byte field indicating the sequence number of the LSP. It helps distinguish multiple LSPs generated by the same router for the same level.

Internet – This community attribute allows a route to be advertised to any BGP peer, including EBGP and IBGP. This is the default behavior if no other restrictive community is attached.

No_Advertise – Prevents the route from being advertised to any peer.

No_Export – Prevents the route from being advertised to EBGP peers.

No_Export_Subconfed – Restricts the route from being advertised outside the sub-AS in a confederation.

Reference from Huawei HCIP-Datacom-Core Technology Study Guide:

“The Internet community attribute allows unrestricted advertisement of a route. Other community attributes like No_Advertise and No_Export limit route propagation.”

(Chapter: BGP Community Attributes – Section: Well-known Communities)