H12-821_V1.0 Huawei HCIP-Datacom-Core Technology V1.0 Free Practice Exam Questions (2026 Updated)

Hello packets are the most basic and essential type of OSPF packets used for the following purposes:

Neighbor discovery – Routers use Hello packets to discover other OSPF routers on the same link.

Neighbor relationship establishment – When two routers exchange matching Hello packets, they move from the "Init" state to "2-Way" and further into adjacency states.

Neighbor relationship maintenance – Hello packets are sent periodically to ensure that neighbors are still reachable. If Hello packets are missed within the dead interval, the neighbor is considered down.

Neighbor deletion is not a direct function of Hello packets. Neighbor deletion results indirectly from missed Hello packets.

In dual-link MSB networking with load balancing, the new AP will connect to the AC with the lower number of connected APs. In this case, AC2 has only 20 connected APs, while AC1 has 100. Therefore, the new AP will connect to AC2 ​.

 In asynchronous mode, BFD control packets are exchanged periodically to detect faults.

 In demand mode, once the session is established, BFD stops sending periodic control packets and relies on external mechanisms to verify connectivity.

 Asynchronous mode is the most commonly used mode. However, the Echo function is supported in asynchronous mode, making Option B incorrect ​.

Comprehensive and Detailed Step-by-Step Explanation:

1. Understanding IGMP Version Compatibility:

IGMP (Internet Group Management Protocol) supports multiple versions, such as IGMPv1, IGMPv2, and IGMPv3.

A device running a later version of IGMP is backward-compatible and can identify Report messages from earlier versions.

However, a device running an earlier version of IGMP cannot recognize the newer features or formats of later IGMP versions.

2. Best Practice:

To avoid compatibility issues, the IGMP version configured on the switch should be the same as or later than the version used by the member hosts in the network.

3. Why the Statement is TRUE:

The statement is correct because it describes the compatibility behavior of IGMP versions and advises setting the switch IGMP version appropriately.

Comprehensive and Detailed in-depth Step-by-Step Explanation:

The Network Entity Title (NET) is a unique identifier assigned to an IS-IS router. It is derived from the Network Service Access Point (NSAP) address and consists of the following components:

Area Address:

Identifies the area in which the router resides.

Multiple routers in the same IS-IS area must have the same area address.

System ID:

Uniquely identifies the router within the IS-IS area.

The System ID is typically derived from the router's loopback IP address or another unique value.

SEL (Selector Field):

The SEL field is always set to 00 for IS-IS NETs.

The NET is used by IS-IS for route calculation and to identify the router within the IS-IS domain. Therefore, the statement is TRUE.

Comprehensive and Detailed Step-by-Step Explanation:

Switch Stack Overview:

In a switch stack, roles are assigned as master, standby, and slave.

The master handles configuration and control, while the standby serves as the backup master.

Behavior During Master Restart:

D: If the master switch restarts, the standby switch immediately takes over as the new master.

B: After the original master switch restarts, it becomes the master again (default behavior).

Incorrect Options:

A: The slave switch is not promoted to standby before the master switch restart completes.

C: The original standby switch remains the master after the restart.

Comprehensive and Detailed Step-by-Step Explanation:

1. What is the BFD Echo Function?

BFD (Bidirectional Forwarding Detection) is used to detect link failures.

The Echo function is an optional feature that tests link connectivity by looping back packets sent from the local device through the forwarding path.

2. Analysis of Each Statement:

Option A: If URPF is enabled on the peer end, BFD packets may be incorrectly discarded on the peer end.

Correct.

URPF (Unicast Reverse Path Forwarding) checks whether the source IP address of an incoming packet is reachable via the interface it was received on. Since the Echo function uses loopback packets, this can conflict with URPF, causing the packets to be dropped.

Option B: In the BFD Echo function, the device uses the IP address of the outbound interface as the source IP address by default.

Correct.

By default, the outbound interface's IP address is used as the source address for BFD Echo packets.

Option C: The BFD Echo function applies only to single-hop BFD sessions.

Incorrect.

The BFD Echo function can be used for both single-hop and multi-hop BFD sessions.

Option D: When configuring a BFD session supporting the BFD Echo function, you need to configure both the local and remote discriminators.

Incorrect.

The BFD Echo function is locally configured and does not require setting remote discriminators. The function operates independently of the remote device's configuration.

3. Summary:

The correct statements are A and B.