Fire-Inspector-II International Code Council 67 - Fire Inspector II Exam Free Practice Exam Questions (2025 Updated)

High-Pile Combustible Storage Permit Requirements

According to the International Fire Code (IFC) 2021, Section 105.6.23, a permit is required for the storage of high-pile combustible stock when the storage area exceeds 2,500 square feet.

2. Definition of High-Pile Storage

High-pile storage is defined as storage of combustible materials on racks or piles exceeding 12 feet in height (or 6 feet for highly combustible materials, such as rubber and plastics).

IFC Table 3206.2 establishes fire protection requirements based on storage height, area, and commodity class.

3. Verification of Other Options

Option A (225 sq. ft.) – Incorrect, as this is far below the 2,500 sq. ft. permit threshold.

Option B (500 sq. ft.) – Incorrect, as the fire code does not require a permit at this level.

Option C (1,000 sq. ft.) – Incorrect, as the IFC specifies 2,500 sq. ft. as the threshold for requiring a permit.

Reference Sources:

International Fire Code (IFC) 2021 – Section 105.6.23 (High-Pile Combustible Storage Permit Requirements)

IFC Chapter 32 (High-Piled Storage Regulations)

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: D. 2,500. ✅

In organic coating processes where Class I liquids are exposed to air, fire codes require Class I, Division I electrical installations in hazardous locations to prevent ignition of flammable vapors.

The "immediate vicinity" around pumps or equipment where vapors may accumulate extends 10 feet horizontally from the vapor liberation point in all directions.

Reference to Fire Inspector Documentation:

1. 2021 International Fire Code (IFC) – Section 1503.2.1 (Electrical Installations in Organic Coating Processes)

IFC 1503.2.1 requires that electrical components must be rated for Class I, Division I within 10 feet of vapor sources.

This prevents ignition hazards in locations with flammable vapors.

2. NFPA 33 – Standard for Spray Application Using Flammable or Combustible Materials (2021 Edition) – Section 6.5.2

NFPA 33, Section 6.5.2 states that a 10-foot horizontal zone is considered hazardous and requires Class I, Division I electrical installation.

Detailed Explanation of Answer Choices:

Option A (Incorrect): 5 feet is too short and does not provide sufficient protection from vapor migration.

Option B (Correct): 10 feet is the correct required distance per IFC 1503.2.1 and NFPA 33.

Option C (Incorrect): 20 feet is beyond the required hazardous zone.

Option D (Incorrect): 50 feet is excessive and not required by code.

Thus, the correct and verified answer is: B. 10.

The requirement for panic hardware on exit doors is specified in 2021 IFC Section 1010.2.9 – Panic and Fire Exit Hardware.

IFC Section 1010.2.9.1 – Where Panic Hardware is Required:

Panic hardware is required for Group A (Assembly) occupancies when the occupant load is 50 or more.

It is also required in certain Group E (Educational) and Group R-1 (Hotels and Dormitories) occupancies under specific conditions.

Why Other Options Are Incorrect?

A. 10; A – The threshold for panic hardware in Group A occupancies is 50, not 10.

C. 50; M – Group M (Mercantile) does not require panic hardware unless specifically required by another section of the code.

D. 100; F – Panic hardware is not required in Group F (Factory) occupancies at 100 occupants; the threshold applies primarily to Group A.

Paint Spray Booth Clearance Requirements

According to the International Fire Code (IFC) 2021, Section 2404.3.2, paint spray booths must have a minimum clearance of 18 inches from unprotected combustible materials.

This clearance requirement helps prevent heat transfer, fire spread, and ignition of nearby combustible materials due to the operation of the spray booth.

2. Why 18 Inches is the Correct Answer

Spray booths generate overspray, vapors, and heat, making clearance essential for fire prevention.

The requirement applies to combustible walls, ceilings, and storage materials surrounding the spray booth.

If combustibles are within 18 inches, additional fire protection such as fire-rated barriers or sprinkler protection may be required.

3. Verification of Other Options

Option A (12 inches) – Incorrect, as the IFC mandates a minimum 18-inch clearance.

Option C (24 inches) – Exceeds the standard clearance requirement but is not the official minimum. Incorrect.

Option D (36 inches) – Some jurisdictions may require larger clearances, but IFC mandates 18 inches as the minimum. Incorrect.

Reference Sources:

International Fire Code (IFC) 2021 – Section 2404.3.2 (Paint Spray Booth Clearance Requirements)

NFPA 33: Standard for Spray Application Using Flammable or Combustible Materials (Clearance Guidelines)

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: B. 18 inche

 Reference to Occupant Load Factor Calculations:

The International Fire Code (IFC 2021), Table 1004.5 provides occupant load factors for different types of occupancies.

For assembly occupancy with tables and chairs, the occupant load factor is 15 square feet per person (net area).

 Calculation of Occupant Load:

Formula: Occupant Load=Net Square FootageOccupant Load Factor\text{Occupant Load} = \frac{\text{Net Square Footage}}{\text{Occupant Load Factor}}Occupant Load=Occupant Load FactorNet Square Footage​

Given: 2,500 net square feet, with a load factor of 15 sq. ft. per person: 250015=166.67≈167 occupants\frac{2500}{15} = 166.67 \approx 167 \text{ occupants}152500​=166.67≈167 occupants

 Clarification of Incorrect Answer Choices:

A. 167 → Correct

Matches the exact IFC Table 1004.5 calculation.

B. 227 → Incorrect

Would correspond to a lower load factor (about 11 sq. ft. per occupant), which is not the standard for tables and chairs.

C. 357 → Incorrect

Would correspond to a 7 sq. ft. per occupant factor, used for tighter seating arrangements (e.g., assembly without fixed seats).

D. 500 → Incorrect

Would correspond to a 5 sq. ft. per occupant factor, typically used for standing areas or dense seating arrangements.

 Conclusion:

The correct and verified answer is A (167 occupants) based on IFC Table 1004.5, using the standard occupant load factor for assembly occupancies with tables and chairs.