Fire-Inspector-II International Code Council 67 - Fire Inspector II Exam Free Practice Exam Questions (2025 Updated)

 Reference to Fire Code Requirements for Clearance Between Combustible Fibers and Sprinklers:

The International Fire Code (IFC 2021), Section 3206.6, states that the minimum clearance between the tops of piles of combustible fibers and sprinkler deflectors shall be no less than 3 feet.

This requirement ensures that the sprinkler system operates efficiently and that water distribution is not obstructed in case of a fire.

 Fire Safety Concerns:

Combustible fibers pose a high fire risk due to their flammability and tendency to generate large amounts of heat and smoke.

Adequate clearance prevents heat accumulation near the sprinkler heads, ensuring they activate at the correct temperature.

 Clarification of Incorrect Answer Choices:

A. 2 ft. → Incorrect

Too low and could obstruct sprinkler operation, reducing water distribution effectiveness.

C. 4 ft. → Incorrect

Exceeds the required minimum per the IFC 3206.6 standard, though more clearance is beneficial.

D. 5 ft. → Incorrect

More than the code requirement, but the mandatory clearance is 3 feet.

 Conclusion:

The correct and verified answer is B (3 feet) based on IFC 3206.6, ensuring proper sprinkler performance and fire safety for combustible fiber storage.

The storage of flammable medical gas supply cylinders inside a building is regulated by 2021 International Fire Code (IFC) Section 5306 – Medical Gas Systems.

IFC Section 5306.2.1 – Storage of More Than 200 Cubic Feet of Medical Gases:

When the quantity of flammable medical gas exceeds 200 cubic feet, it must be stored in a separate room with a minimum 2-hour fire-resistance rating.

The room must also comply with ventilation and explosion control requirements per NFPA 99 (Healthcare Facilities Code).

Why Other Options Are Incorrect?

A. 1/2-hour – Insufficient fire resistance for high-risk gas storage.

B. 1-hour – Does not meet the minimum 2-hour requirement set by the IFC.

D. 3-hour – Exceeds the minimum required by code; the correct requirement is 2-hour fire-resistive construction.

The occupant load for an R-2 building's common patio area must be calculated using an occupant load factor. The correct factor is 15 gross sq. ft. per person.

Reference to Fire Inspector Documentation:

1. 2021 International Building Code (IBC) – Table 1004.5 (Occupant Load Factor)

For outdoor areas (such as patios and terraces), the applicable factor is 15 gross sq. ft. per person.

2. 2021 International Fire Code (IFC) – Section 1004.5 (Outdoor Occupant Loads)

The 15 gross per person requirement is applied to common outdoor gathering areas in residential occupancies (R-2).

Detailed Explanation of Answer Choices:

Option A (Incorrect): 50 net per person applies to storage areas, not patios.

Option B (Incorrect): 11 gross per person is used for business occupancies (B), not residential patios.

Option C (Correct): 15 gross per person is the correct calculation factor for common outdoor spaces in R-2 buildings.

Option D (Incorrect): The code official does not assign occupant load values arbitrarily—they follow IBC Table 1004.5.

Thus, the correct and verified answer is: C. 15 gross per person.

Retention of Fire Code-Related Records

According to the International Fire Code (IFC) 2021, Section 104.6, records related to code enforcement decisions, including modifications or substitutions (such as a sprinkler system replacing a second exit), must be retained for as long as the building and the condition exist.

This ensures that future inspections, property owners, and authorities can verify past decisions and compliance history.

2. Why the Records Must Be Retained Permanently

Modifications that impact life safety (such as exit requirements) must remain on record for the lifetime of the building to ensure ongoing compliance and safety.

If the condition (sprinkler substitution for an exit) still exists, any future inspector or building official must be able to verify the original approval and rationale.

3. Verification of Other Options

Option A (Five years) – Incorrect, as fire code modifications must remain on record permanently if they affect egress or fire protection systems.

Option B (Three years) – Incorrect, as this timeframe applies to temporary inspection reports, not major code modifications.

Option C (Until the building is sold) – Incorrect, as ownership changes do not affect the need for record retention on fire safety decisions.

Reference Sources:

International Fire Code (IFC) 2021 – Section 104.6 (Fire Code Record Retention Requirements)

NFPA 1: Fire Code (Retention of Code-Related Decisions)

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: D. For as long as the building and the condition exist. ✅

1.

Exit Sign Letter Height Requirement

According to the International Fire Code (IFC) 2021, Section 1013.5, and the International Building Code (IBC) 2021, Section 1013.5, exit sign letters must be at least 6 inches in height. However, the minimum height requirement for the wording within the sign (e.g., "EXIT") is specifically 4 inches.

The stroke width of these letters must be at least 0.5 inches to ensure visibility.

2. Verification of Other Options

Option A (three inches) – Below the minimum height requirement. Incorrect.

Option C (five inches) – Exceeds the minimum standard but is not the correct minimum required size. Incorrect.

Option D (six inches) – This applies to the total EXIT sign height, but the actual letter requirement is 4 inches. Incorrect.

Reference Sources:

International Fire Code (IFC) 2021 – Section 1013.5

International Building Code (IBC) 2021 – Section 1013.5

NFPA 101: Life Safety Code (Exit Sign Requirements)

Definition of Extra-High-Rack Combustible Storage

According to International Fire Code (IFC) 2021, Section 3206.6, extra-high-rack combustible storage is defined as:

Class I, II, III, or IV commodities stored on racks exceeding 40 feet in height.

High-hazard commodities stored on racks exceeding 30 feet in height.

2. Understanding Rack Storage Classifications

Class I-IV Commodities: These refer to general, moderate-risk combustible materials such as wood, paper, and plastics.

High-Hazard Commodities: These are materials that have a higher fire risk, such as highly combustible plastics, flammable solids, and products prone to rapid heat release.

3. Verification of Other Options

Option A (20; 30) – Incorrect, as 40 feet is the correct threshold for Class I-IV commodities.

Option B (30; 40) – Incorrect, as 30 feet applies to high-hazard commodities, not Class I-IV commodities.

Option D (50; 40) – Incorrect, as the correct heights are 40 feet and 30 feet, respectively.

Reference Sources:

International Fire Code (IFC) 2021 – Section 3206.6 (Definition of Extra-High-Rack Storage)

NFPA 13: Standard for the Installation of Sprinkler Systems (High-Rack Storage Requirements)

ICC Fire Inspector II Study Guide (2021)

The occupant load of a space is determined using the 2021 International Building Code (IBC), Table 1004.5 – Maximum Floor Area Per Occupant.

IBC Table 1004.5 – Occupant Load Factor for Exercise Rooms:

The occupant load factor for an exercise room is 1 person per 20 square feet.

Given that the exercise room is 1,000 sq. ft.:

1,000 sq. ft. ÷ 20 sq. ft. per person = 50 occupants

Why Other Options Are Incorrect?

A. 10 – Would require a 100 sq. ft. per person load factor, which is not applicable for exercise rooms.

B. 20 – Incorrect calculation; using the correct load factor, the actual number is 50.

C. 30 – Also incorrect based on the proper load factor.

✅ Correct Answer: D. 50

Aisle Width Requirements for Baled Fiber Storage

According to the International Fire Code (IFC) 2021, Section 3206.9, blocks or piles of baled fiber must be separated by aisles at least 5 feet wide to allow for proper fire department access and fire prevention measures.

This regulation applies to combustible fibers such as cotton, jute, and hemp, which are highly flammable and can quickly contribute to fire spread.

2. Why 5 Feet is the Correct Answer

Adequate aisle spacing prevents fire from spreading rapidly between storage piles.

The 5-foot minimum width allows for fire suppression efforts and emergency personnel access.

Insufficient aisle width can trap heat and flames, increasing the severity of a fire incident.

3. Verification of Other Options

Option A (3 feet) – Incorrect, as this does not meet the minimum IFC requirement of 5 feet.

Option C (8 feet) – Incorrect, as the IFC requires a minimum of 5 feet, although wider aisles may be used based on facility layout.

Option D (10 feet) – Incorrect, since 5 feet is the standard requirement, though wider aisles may be beneficial for larger storage facilities.

Reference Sources:

International Fire Code (IFC) 2021 – Section 3206.9 (Aisle Width for Baled Fiber Storage)

NFPA 1: Fire Code – Storage of Combustible Fibers Regulations

ICC Fire Inspector II Study Guide (2021)

Smoke alarm requirements for individual guest rooms in hotels are specified in the 2021 International Fire Code (IFC) Section 907.2.11.3 and NFPA 72 (National Fire Alarm and Signaling Code).

IFC 907.2.11.3 – Smoke Alarms in Group R-1 Occupancies (Hotels and Motels):

Requires smoke alarms in sleeping areas to be interconnected so that when one alarm is activated, it will trigger all alarms within the guest room or suite.

This ensures that occupants in different areas of the same guest room are alerted simultaneously to fire hazards.

Why Other Options Are Incorrect?

A. Their batteries must be checked every six months.

The IFC and NFPA 72 require smoke alarm batteries to be checked, but they do not mandate a six-month inspection schedule.

B. They must automatically sound a fire alarm throughout the hotel.

Smoke alarms within an individual guest room do not have to activate the entire hotel’s fire alarm system.

C. They must initiate an automatic fire suppression or sprinkler system.

Smoke alarms are designed for early detection and warning, not for activating fire suppression systems.

✅ Correct Answer: D. They must be interconnected so that one alarm will activate all alarms within the guest rooms.

Fire Extinguisher Requirements for Hot Work Locations

According to the International Fire Code (IFC) 2021, Section 3504.2.6, one or more approved fire extinguishers must be located within 30 feet of hot work locations.

Hot work includes welding, cutting, grinding, brazing, or any operation that generates heat, sparks, or flames.

2. Why 30 Feet is the Correct Answer

Hot work presents a high fire risk, and quick access to fire extinguishers is crucial for immediate response.

The 30-foot requirement ensures that extinguishers are readily accessible without obstructing the work area.

3. Verification of Other Options

Option A (20 feet) – Incorrect, as the IFC mandates a 30-foot minimum distance.

Option C (40 feet) – Incorrect, as this exceeds the maximum distance allowed under the fire code.

Option D (50 feet) – Incorrect, as fire extinguishers must be closer to provide effective fire suppression.

Reference Sources:

International Fire Code (IFC) 2021 – Section 3504.2.6 (Fire Extinguishers for Hot Work)

NFPA 51B: Standard for Fire Prevention During Welding, Cutting, and Other Hot Work

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: B. 30 feet. ✅

 Reference to Ventilation Requirements for Flammable Liquids:

The International Fire Code (IFC 2021), Section 5004.3.7.3, and NFPA 30 (Flammable and Combustible Liquids Code), Section 18.5.4.1 specify the ventilation requirements for the use, dispensing, and mixing of flammable liquids in open systems.

Continuous mechanical ventilation must be provided at a minimum rate of 2 CFM per square foot of floor area.

 Reason for Ventilation Requirements:

Flammable liquids release vapors that can ignite at low concentrations, creating fire and explosion hazards.

Proper ventilation removes vapors to prevent them from reaching flammable limits in the air.

 Clarification of Incorrect Answer Choices:

A. 1 CFM per sq. ft. → Incorrect

Too low to effectively control flammable vapor accumulation.

C. 3 CFM per sq. ft. → Incorrect

While more ventilation can be beneficial, the minimum required by code is 2 CFM per sq. ft.

D. 4 CFM per sq. ft. → Incorrect

Exceeds the code-mandated minimum requirement, though higher ventilation rates may be required based on specific hazards.

 Conclusion:

The correct and verified answer is B (2 CFM per sq. ft.), based on IFC 5004.3.7.3 and NFPA 30 Section 18.5.4.1, ensuring safe handling of flammable liquids in open systems.

 Reference to Halon 1211 Hand-Hose-Line System Requirements:

NFPA 12A (Standard on Halon 1211 Fire Extinguishing Systems), Section 6.5, states that all hoses for high-pressure Halon 1211 hand-hose-line systems must be tested at 1,500 psi to ensure they can withstand operational pressure without failure.

The International Fire Code (IFC 2021), Section 904.10, also references the requirements for Halon 1211 systems, ensuring proper testing for system integrity.

 Purpose of Pressure Testing:

High-pressure Halon 1211 systems operate under significant force, and hose failures could result in loss of fire suppression capability or safety hazards.

Testing at 1,500 psi ensures hoses can handle peak pressures without rupture or degradation over time.

 Clarification of Incorrect Answer Choices:

A. 600 psi → Incorrect

Too low for high-pressure systems, insufficient to verify hose integrity.

B. 900 psi → Incorrect

Below the required 1,500 psi standard for high-pressure Halon 1211 hoses.

D. 2,500 psi → Incorrect

Exceeds the required test pressure per NFPA 12A; unnecessary over-testing could damage hoses.

 Conclusion:

The correct and verified answer is C (1,500 psi) based on NFPA 12A and IFC 904.10, ensuring compliance with Halon 1211 high-pressure system testing standards.

IFC Section 903.3.5 and Appendix B (Fire-Flow Requirements) allow a reduction in fire flow when sprinklers are installed. For a Type II-B building (noncombustible, unprotected), the base fire flow (7,000 gpm) reflects a large, unsprinklered structure (e.g., per Table B105.1(2)). With full sprinkler protection, IFC B105.2 permits a reduction to as low as 25% of the original flow or the sprinkler demand (whichever is greater), typically 1,500 gpm for commercial buildings per NFPA 13 standards, assuming adequate water supply. Options B, C, and D exceed this minimum without justification. Thus, A is correct.

For Group I-2 occupancies (such as hospitals, nursing homes, and similar healthcare facilities), horizontal exits are used to improve fire safety by allowing occupants to move to a safer area without using stairs or elevators.

IFC 2021, Section 1026.1 (Horizontal Exits – General Requirements) states that:

Horizontal exits shall not comprise more than one-half (1/2) of the required exits from any floor area in a Group I-2 occupancy.

This ensures that at least 50% of the required exits remain traditional vertical or exterior exits, maintaining a balance between horizontal and traditional egress routes.

✅ Correct Answer: B. 1/2

To determine the maximum occupant load for a bowling center with 25 lanes and 3,500 sq. ft. of additional area, we use the occupant load factor from 2021 IBC Table 1004.5.

Step 1: Calculate the Occupant Load for Bowling Lanes

IBC Table 1004.5 assigns 50 sq. ft. per person for bowling lanes and associated seating areas.

With 25 lanes, assuming 100 sq. ft. per lane (standard industry measurement for lane width and approach area):

25×(10050)=25×2=50 occupants25 \times \left( \frac{100}{50} \right) = 25 \times 2 = 50 \text{ occupants}25×(50100​)=25×2=50 occupants

Step 2: Calculate the Occupant Load for Additional Area

Additional 3,500 sq. ft. area follows a general occupant load factor of 15 sq. ft. per person (assembly without fixed seats):

3,50015=233.3 occupants≈234 (rounded)\frac{3,500}{15} = 233.3 \text{ occupants} \approx 234 \text{ (rounded)}153,500​=233.3 occupants≈234 (rounded)

Final Calculation:

50+184=234 occupants50 + 184 = 234 \text{ occupants}50+184=234 occupants

Reference to Fire Inspector Documentation:

1. 2021 International Building Code (IBC) – Table 1004.5 (Occupant Load Factor)

Bowling lanes require 50 sq. ft. per person.

Assembly areas without fixed seats use 15 sq. ft. per person.

2. 2021 International Fire Code (IFC) – Section 1004.1.2 (Areas without Fixed Seating)

When calculating occupant load, areas without fixed seating must be divided by the appropriate occupant load factor.

Detailed Explanation of Answer Choices:

Option A (Incorrect): 125 is too low based on correct load factor calculations.

Option B (Correct): 234 is the correct calculation using IBC Table 1004.5.

Option C (Incorrect): 500 is too high based on the available space.

Option D (Incorrect): 625 significantly overestimates the actual occupant load.

Thus, the correct and verified answer is: B. 234.

IFC Section 901.5 (Acceptance Tests) requires fire protection systems, including fire alarms, to be tested upon completion to ensure compliance with NFPA 72 (National Fire Alarm and Signaling Code) and the IFC. The contractor’s verification of full compliance (B) signals readiness for the official acceptance test by the fire code official, ensuring all components are installed and functional. Option A (zone-by-zone testing) is impractical for final acceptance. Option C ties the test to water supply, irrelevant to alarms. Option D (one year) is excessive and not required by IFC or NFPA 72 for initial acceptance. Thus, B is correct.

 Reference to LP-Gas Tank Separation Requirements:

The International Fire Code (IFC 2021), Table 6104.3, provides minimum separation distances for above-ground LP-gas tanks based on capacity and proximity to each other or property lines.

According to Table 6104.3, for an LP-gas tank with a 501-gallon capacity located near a 250-gallon tank, the required minimum separation distance from adjoining property is 10 feet.

 Why Separation Distance is Important:

LP-gas is highly flammable, and inadequate separation distances increase the risk of fire spread and explosion hazards.

Proper spacing ensures safety for occupants, emergency responders, and nearby properties.

 Clarification of Incorrect Answer Choices:

A. 5 ft. → Incorrect

Too close per IFC 6104.3; does not meet safety requirements.

C. 20 ft. → Incorrect

20 feet is required for larger tanks, but not for the combined 501-gal. and 250-gal. tank setup.

D. 25 ft. → Incorrect

Greater than the required minimum; while more distance is safer, IFC mandates a minimum of 10 feet.

 Conclusion:

The correct and verified answer is B (10 feet) based on IFC 6104.3, ensuring safe LP-gas tank separation from adjoining properties.

Understanding Type III Construction

According to the International Building Code (IBC) 2021, Section 602.3, Type III construction is a mix of noncombustible and combustible materials.

Exterior walls must be noncombustible or fire-retardant-treated wood, while interior structural elements (such as floors, roofs, and partitions) can be wood.

2. Common Uses of Type III Construction

Churches, schools, apartment buildings, and mercantile (retail) structures are often built using Type III construction because it balances fire resistance with cost-effectiveness.

Many low-rise residential and commercial buildings use this type due to its ability to support multiple stories while maintaining some fire protection.

3. Verification of Other Options

Option A (Type I) – Incorrect, as Type I construction is entirely noncombustible (steel/concrete) and used for high-rises, not typical for churches, schools, or apartments.

Option B (Type II) – Incorrect, as Type II construction is fully noncombustible but has lower fire resistance than Type I, mainly used for commercial buildings, warehouses, and low-rise offices.

Option D (Type IV) – Incorrect, as Type IV (heavy timber) is rarely used for schools and apartments, though some older churches may use it.

Reference Sources:

International Building Code (IBC) 2021 – Section 602.3 (Type III Construction Definition)

NFPA 220: Standard on Types of Building Construction

ICC Fire Inspector II Study Guide (2021)

Thus, the correct and verified answer is: C. Type III. ✅

 Reference to Flammable Liquids Storage Cabinet Requirements:

According to The International Fire Code (IFC 2021), Section 5704.3.2 and NFPA 30 (Flammable and Combustible Liquids Code), Section 9.5.3, the maximum amount of Class II and Class III liquids that can be stored in a flammable liquids storage cabinet is 120 gallons.

This limit ensures safe containment, fire protection, and reduced risk of liquid ignition or spillage.

 Understanding Class II and III Liquids:

Class II liquids: Flash point between 100°F and 140°F (e.g., diesel fuel, kerosene).

Class III liquids: Flash point above 140°F (e.g., motor oil, cooking oils).

While these liquids are less volatile than Class I liquids, they still pose a fire risk, requiring proper storage in approved cabinets.

 Clarification of Incorrect Answer Choices:

A. 10 gallons → Incorrect

Too low; IFC and NFPA allow up to 120 gallons in storage cabinets.

B. 60 gallons → Incorrect

This is the maximum for Class I liquids, but Class II and III liquids are allowed up to 120 gallons.

D. 240 gallons → Incorrect

Exceeds the allowable limit per IFC 5704.3.2 and NFPA 30, which set the maximum at 120 gallons per cabinet.

 Conclusion:

The correct and verified answer is C (120 gallons) as per IFC 5704.3.2 and NFPA 30, ensuring compliance with flammable liquids storage safety standards.