LEED-AP-BD+C USGBC LEED AP Building Design + Construction (LEED v5 AP BD+C) Free Practice Exam Questions (2026 Updated)

Smoking tobacco products must be prohibited within a building as a prerequisite to LEED certification, according to the Indoor Environmental Quality Prerequisite, Environmental Tobacco Smoke Control1. This prerequisite aims to prevent or minimize exposure of building occupants, indoor surfaces, and ventilation air distribution systems to environmental tobacco smoke (ETS), which is a known human carcinogen and a source of indoor air pollution2. The prerequisite requires the project to meet one of the following options:

Option 1. No Smoking. Prohibit smoking in the building and within 25 feet (8 meters) of all entries, outdoor air intakes, and operable windows.

Option 2. Smoking Areas. Designate smoking areas outside the building and at least 25 feet (8 meters) from all entries, outdoor air intakes, and operable windows. If smoking areas are enclosed, they must be negatively pressurized and vented directly to the outdoors. Prohibit smoking in all common areas of residential buildings and provide signage to indicate smoking and nonsmoking areas.

The other activities, such as burning fossil fuels, preparing non-organic foods, and manufacturing toxic chemicals, are not explicitly prohibited by any LEED prerequisites, although they may have negative impacts on the environment, health, and energy performance of the building.

The Owner’s Project Requirements (OPR) is the document that should be used to record the project goals to be used throughout the design of the project. The OPR is a written document that details the ideas, concepts, and criteria that are determined by the owner to be important to the success of the project1. The OPR is developed during the pre-design phase and is used as a basis for the design team to prepare the Basis of Design (BOD), which describes how the design of the building systems meets the OPR2. The OPR is also used to evaluate the design, construction, and commissioning of the project to ensure that the owner’s expectations are met3.

One of the requirements for attempting a pilot credit is to complete a feedback survey after submitting the project for review. TheLEED V5Reference Guide for Building Design and Construction states that " the project team must complete a feedback survey for each pilot credit attempted. The survey link is provided in the pilot credit language. The survey must be completed after the project has been submitted for review and before the project receives a final rating " 1. The feedback survey is an important tool for USGBC to evaluate the effectiveness and applicability of the pilot credit, and to make improvements or modifications based on the project team’s experience.

LEED v5 recognizes operable windows as a passive resilience strategy under EQc4: Resilient Spaces. During events such as power outages or mechanical-system interruptions, operable windows can provide natural ventilation when outdoor conditions are appropriate, maintaining airflow and reducing dependence on mechanical ventilation. This can help remove accumulated heat and indoor contaminants and improve survivability when normal building services are unavailable. Increasing thermal mass is an envelope strategy, but opening windows does not increase the mass of the building. Seasonal thermal adaptation is relevant to occupant comfort, but the principal resilience function of an operable window is its ability to provide passive ventilation when mechanical systems cannot operate normally. Therefore, Option B most directly describes the LEED v5 resilience benefit associated with operable windows.

Temporary wood products cannot be included in the calculations for the Materials and Resources Credit, Building Disclosure and Optimization - Sourcing of Raw Materials, Option 2. Leadership Extraction Practices. This is because the credit only applies to permanently installed building products, not to products purchased for temporary use on the project1. The other options are false. If any temporary wood materials are included in the calculation, they must be excluded from the total value of permanently installed building products1. Non-certified wood materials do not contribute to other credits, unless they meet other criteria such as recycled content or regional materials2. FSC-certified wood materials purchased for more than one project cannot be applied to other projects seeking LEED certification, unless they are reused or salvaged materials3.

Detailed Explanation:

For the Surrounding Density and Diverse Uses credit, LEED requires project teams to calculate residential and non-residential densities within a 1/4-mile (0.40 km) radius of the project boundary. This measurement ensures that projects are located in areas with sufficient infrastructure and services to reduce dependency on vehicles and promote walkability.

TheCommissioning Authority (CxA)plays a key role in ensuringbuilding systems meet the Owner’s Project Requirements (OPR).

TheCxA must review the OPRto confirm that design and construction decisions align with theowner ' s sustainability and performance goals.

TheCxA should be independentandcannot be part of the project ' s design or construction management teamif the project is larger than 20,000 sq. ft.

TheCxA reports findings to the owner, not the architect.

While experience is required,LEED does not specify that only one project is neededfor eligibility.

(Source: Official LEED BD+C Reference Manual)

For SSc2: Accessible Outdoor Space, at least 25% of the qualifying outdoor space must be vegetated, have overhead vegetated canopy, or incorporate an appropriate natural feature. Therefore, Option B is correct. The space must also be physically accessible and designed for meaningful occupant use rather than functioning merely as inaccessible roof landscaping. Walkways, seating areas, and fountains can establish an occupant-oriented outdoor environment, while the vegetated portion supports ecological performance, restorative contact with nature, stormwater benefits, and reduced hardscape impacts. A qualifying vegetated roof can contribute when it is accessible and configured as usable outdoor space. The 20% option is below the required threshold, while 30% incorrectly treats the broader outdoor-space provision as the minimum vegetated percentage.

LEED v5 EQp2: Fundamental Air Quality directly references ASHRAE Standard 62.1-2022 for indoor ventilation and air-quality design. Projects must investigate regional and local outdoor air quality in accordance with Sections 4.1 through 4.3 and satisfy ventilation and filtration requirements using applicable portions of Sections 5 and 6. The ventilation rate procedure, indoor air quality procedure, natural ventilation procedure, or an allowed combination may be used. ASHRAE Standard 55 addresses thermal environmental conditions and occupant thermal comfort rather than minimum ventilation. ASHRAE 90.1 primarily addresses building energy efficiency. Therefore, neither Standard 55 nor Standard 90.1 establishes the fundamental ventilation requirements requested by EQp2. The correct referenced standard for this prerequisite is ASHRAE 62.1-2022, making Option C correct.

The Energy and Atmosphere Prerequisite, Minimum Energy Performance, Option 2. Prescriptive Compliance: ASHRAE 50% Advanced Energy Design Guide allows projects to follow the recommendations of the ASHRAE 50% Advanced Energy Design Guides (AEDGs) for different building types and climate zones. The AEDGs provide design guidance for buildings that use 50% less energy than those built to the requirements of the ANSI/ASHRAE/IES Standard 90.1-2004 commercial code1. However, not all building types and sizes are covered by the AEDGs. According to the LEED Reference Guide for Building Design and Construction2, the following building types and sizes are eligible for this option:

Small to Medium Office buildings up to 100,000 ft2 (9 290 m2)

Medium to Large Retail buildings up to 100,000 ft2 (9 290 m2)

K-12 School buildings up to 200,000 ft2 (18 580 m2)

Warehouse and Distribution Center buildings up to 500,000 ft2 (46 450 m2)

Therefore, among the given options, only the school project is eligible to pursue this option, as it falls within the size limit for the K-12 School AEDG3.

The project should first conduct a feasibility study to identify the quantity, quality, timing, and reliability of available alternative water sources. Potential sources may include graywater, rainwater, foundation drainage, condensate, or treated wastewater. The study should compare supply with anticipated nonpotable demands, evaluate storage and treatment requirements, identify regulatory constraints, and estimate capital and operating costs. Metering is important after a viable system has been designed because it verifies performance and identifies abnormal consumption, but meters cannot compensate for an inadequate or unreliable source. Treatment-energy analysis is also necessary, but it should occur within the broader feasibility assessment. Establishing whether sufficient reusable water is actually available is therefore the essential first step in developing an effective water-reuse strategy.

Energy-storage systems enhance grid interactivity because they can actively change when the building obtains or supplies electrical energy. Batteries may charge during periods of low demand, low electricity prices, or abundant renewable generation and discharge during peak-demand periods or grid emergencies. This reduces peak loads, supports grid reliability, and can maintain selected building functions during outages. Smart meters provide valuable consumption data but do not independently shift or supply energy. Occupancy sensors reduce lighting use when spaces are vacant, but they primarily operate as efficiency controls rather than grid-interactive resources. Energy storage therefore provides the strongest combination of demand management, renewable-energy integration, peak reduction, and resilience. These outcomes align with LEED v5’s focus on operational decarbonization and resilient building performance.

Option 1 of the Innovation credit underLEED V5.1 BD+C rating system (Building Design and Construction) allows for achieving significant, measurable environmental performance using a strategy not addressed in the LEED green building rating system1. Implementing an employee engagement and education plan could be a unique strategy that promotes sustainability and environmental stewardship, which is not specifically addressed in the LEED rating system.

LEED (BD+C)- Innovation Credit: Innovation Option 1

Exterior window shading reduces direct solar heat gain, while operable windows can support passive ventilation and thermal survivability when outdoor conditions permit. Together, these measures directly address extreme-heat exposure and reduce dependence on mechanical cooling. Sump pumps with backup power help manage water entering below-grade or low-lying areas during flooding and remain operational when grid electricity is disrupted. A white roof appropriately addresses heat, but emergency generators do not directly prevent or remove floodwater. A high-efficiency VRF system may reduce normal cooling energy but does not provide passive protection during an outage, while a green roof mainly manages rainfall rather than sea-level flooding. Option C is therefore the only combination in which both measures directly correspond to the identified hazards.

Detailed Explanation:

The energy-related systems analysis must align with the requirements of the Minimum Energy Performance prerequisite. This prerequisite ensures that energy systems are modeled to optimize performance and meet baseline criteria outlined in ASHRAE 90.1-2010 (or applicable standard). Including all system loads and occupants provides a comprehensive understanding of energy demands.

UnderLEED BD+C Energy and Atmosphere (EA) Credit: Renewable Energy Production, renewable biofuels must besustainably sourced and not contaminated.

Non-mill residue forestry biomass wastequalifies asrenewable biofuelbecause it consists ofuntreated wood residuesfrom sustainable forestry operations.

Municipal solid wasteisnot considered renewabledue to its mixed content.

Wood coated with paints, plastics, or resinsisnot renewableas it containsharmful chemicals.

Animal wasteisnot explicitly recognized by LEED as a renewable fuel.

(Source: Official LEED BD+C Reference Manual)

LEED v5 EQp1: Construction Management specifically requires smoking to be prohibited during construction except in designated smoking areas located at least 25 ft. (7.5 m) from the building. The project must also install signage communicating the prohibition. This construction-phase measure protects workers and prevents tobacco smoke from contaminating building materials and indoor environments. Baseline IAQ testing described in Option B occurs after construction and before occupancy and belongs to the Air Quality Testing and Monitoring credit rather than the construction-management prerequisite. Outdoor airflow measurement devices are associated with ventilation-system air-quality requirements and are not the specified construction-phase practice in this scenario. Therefore, establishing designated smoking areas at least 25 ft. from the building is the correct EQp1 construction-management measure. U.S. Green Building Council

The project should use LEED v5 BD+C: New Construction and Major Renovations. The work creates three complete new floors, installs dedicated mechanical systems, adds a mechanical penthouse, and requires structural demolition. This scope is substantially greater than an interior fit-out, so LEED for Commercial Interiors is inappropriate. Under the LEED v5 structure, healthcare buildings are evaluated through the applicable BD+C New Construction and Major Renovations framework rather than through a separately listed LEED for Healthcare rating system. Healthcare-specific operating characteristics must still be addressed when documenting energy, water, resilience, indoor environmental quality, and occupant-experience requirements. The New Construction and Major Renovations rating system is appropriate because the project involves significant new building area, structural alteration, and complete building-system installation.

Interior paint must always be included in Materials and Resources credits.This is because interior paint is considered as a permanently installed product, which is defined by theLEED V5Reference Guide for Building Design and Construction as " a product that is installed in a project permanently or semi- permanently, such that removal would require demolition or substantial renovation. " 1Permanently installed products must be included in the calculations for the following Materials and Resources credits: Building Life-Cycle Impact Reduction, Building Product Disclosure and Optimization - Environmental Product Declarations, Building Product Disclosure and Optimization - Sourcing of Raw Materials, and Building Product Disclosure and Optimization - Material Ingredients.1The other options are not always included in Materials and Resources credits.Faucets (option A) and fire suppression systems (option D) are considered as mechanical, electrical, and plumbing components, which are excluded from the scope of Materials and Resources credits unless they are specifically addressed by the credit requirements.1Furniture (option B) is considered as a non-permanently installed product, whichis optional to include in Materials and Resources credits, except for the Building Product Disclosure and Optimization - Material Ingredients credit, where furniture must be included if it is within the project scope.1References:LEED V5Reference Guide for Building Design and Construction, p.5791;LEED V5Reference Guide for Building Design and Construction, p.5801;LEED V5Reference Guide for Building Design and Construction, p.5811;LEED V5Reference Guide for Building Design and Construction, p.5821;LEED V5Reference Guide for Building Design and Construction, p.5831