300-425 Cisco Designing Cisco Enterprise Wireless Networks (ENWLSD) Free Practice Exam Questions (2026 Updated)

 For optimal Voice over WLAN (VoWLAN) design, a higher data rate is preferred to ensure quality of service and reliability. -67 dBm is a commonly recommended signal level for VoWLAN, and 802.11an, which operates in the 5 GHz band, is capable of supporting higher data rates compared to 802.11bgn, which operates in the 2.4 GHz band. The 5 GHz band is less crowded and prone to interference, making it suitable for high-speed data and voice applications.

FlexConnect APs must be in a FlexConnect group to support 802.11r Fast Transition (FT). This grouping allows for local authentication and key management, which are necessary for fast roaming methods that improve voice quality and wireless IP phone performance during roaming.

In a high-density environment like an auditorium, where APs are in close proximity and a large number of devices are connected, the RF profile is used to adjust the radio frequencies of the APs to minimize co-channel interference. The RF profile allows for the configuration of power levels, channel width, and channel assignment to optimize wireless performance and reduce interference. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide Premium Edition and Practice

Jitter is the variation in time between packets arriving, caused by network congestion, timing drift, or route changes. In a Wi-Fi network designed to support video over Wi-Fi, if video multicast traffic is unreliable despite good coverage, jitter is a key performance metric to investigate. High jitter can cause the video to play erratically, freeze, or have sync issues between video and audio streams

 Cisco FlexConnect mode is designed for branch offices that lack a wired backhaul. It allows APs to switch client data traffic locally while still performing client authentication centrally. This mode provides the flexibility needed for branch deployments, ensuring that client traffic is handled efficiently even if the WAN link to the central site is down. References: Cisco FlexConnect technical documentation and Designing Cisco Enterprise Wireless Networks (ENWLSD) training.

Setting AP fallback to disabled will prevent the AP from moving back to its defined Cisco WLCs automatically after failing over to an undefined controller. This allows manual intervention to determine when the AP should revert to its primary controller.

An SNR (Signal-to-Noise Ratio) less than 15 dB within the cell boundary during an AP-on-a-stick survey indicates that there is interference affecting the AP’s signal. This interference could be from another signal source that is reducing the quality of the connection, despite the signal strength being within the acceptable cell boundary of -67 dBm.

 In an outdoor mesh network designed to cover sports fields, a 5 GHz, 14-dBi patch antenna is suitable for the RAP for backhaul connectivity. The higher gain and directional nature of a patch antenna help in focusing the signal over longer distances and in specific directions, which is ideal for connecting various points in a large outdoor area5.

https://www.cisco.com/c/en/us/products/collateral/wireless/aironet-antennas-accessories/product_data_sheet09186a008008883b.html

To address the sticky client problem, setting an RSSI (Received Signal Strength Indicator) threshold can help. This configuration will prompt clients to roam to a better AP when their signal strength falls below the set threshold, thus enhancing the roaming experience and ensuring clients are connected to the AP with the strongest signal available.

Voice services on a wireless network require a strong and stable signal, as well as low interference and retransmission rates. An RSSI (Received Signal Strength Indicator) of at least -67 dBm is considered the minimum for acceptable voice quality, and -65 dBm is even better, providing a buffer for signal fluctuation. A noise floor of -87 dBm would be too high and could interfere with signal clarity. Retransmission rates should be kept as low as possible; 15% or below is a good target to ensure efficient communication.

 Changing the TPC Power Threshold to -65 dBm would generally result in a decrease in the transmit power of APs to maintain a smaller cell size. This helps in reducing interference and improving overall network performance. A lower threshold means the APs reduce their power to ensure the signal does not exceed -65 dBm, leading to decreased signal strength at the client side.

A Patch antenna should be used to provide wireless coverage on the perimeter of a building while minimizing signal leakage. Patch antennas have a directional radiation pattern that can be focused along the perimeter.

https://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing-combined/industrial-routers-and-industrial-wireless-antenna-guide/ANT-MP-INT-OUT-M.html

 Mobility groups are created by configuring each Wireless LAN Controller (WLC) to use the same mobility domain name and defining each WLC as a peer in the static mobility members list of every other WLC in the group. This configuration allows WLCs to share information and support seamless roaming for wireless clients across different controllers within the same mobility group.

References := Chapter: Chapter 14 - Configuring Mobility Groups - Cisco

 When designing a backhaul link, the mesh AP role should be set to ‘bridge’ to enable it to connect separate network segments or extend coverage to remote areas.

Jammers are non-Wi-Fi interferers that can be identified by Metageek Chanalyzer. They intentionally disrupt wireless communications by emitting radio frequencies that interfere with Wi-Fi signals. Chanalyzer is designed to detect such patterns of interference.

https://www.metageek.com/training/resources/wifi-and-non-wifi-interference